IMG STAGELINE MPX-2 Manual De Instrucciones página 7

– jack DJ MIC (9) for connecting a DJ mono micro-
phone
2) Set the input selector switches (7) for the channels
CH 1 and CH 2 to the corresponding position.
3) Connect the amplifier to the output jacks AMP (14).
4) For sound recordings, connect a sound recorder to
the output jacks REC (13).
5) Connect the supplied plug-in transformer to the jack
(12) and then to a mains socket (230 V~/50 Hz).
After operation disconnect the plug-in transformer
from the mains socket to prevent unnecessary
power consumption.
6) Prior to switching on the mixer, the channel faders
(8) and the volume control of the microphone (5)
should be set to minimum to prevent switching
noise. Then switch on the mixer with the power
switch (2). The LED above the switch lights up to
indicate that the mixer is ready for operation.
7) Finally switch on the units connected.
5 Operation
Prior to setting the mixer into operation for the first
time, set the crossfader (10) to mid-position and un-
lock the TALKOVER switch (3).
Caution! Never adjust the audio system or the head-
phones to a very high volume. Permanent high vol-
umes may damage your hearing! The human ear will
get accustomed to high volumes which do not seem to
be that high after some time. Therefore, do not further
increase a high volume after getting used to it.
5.1 Mixing the audio sources connected
1) Adjust the volume for the input channels CH 1 and
CH 2 with the faders (8) and the volume for the DJ
microphone connected to the jack (9) with the con-
trol MIC LEVEL (5). The stereo output level is indi-
cated by the 5-step LED VU-meter (1). At 0 dB, the
mixer is controlled to its maximum level. In case of
overload, the red LEDs of the VU-meter will light
up.
2) The crossfader allows crossfading between the
channels CH 1 and CH 2. With the crossfader in
mid-position, both channels are fed to the outputs
at the same time.
5.2 Prefader listening to the channels
The prefader listening feature allows individual moni-
toring of the input channels CH 1 and CH 2 via head-
phones. The level of the signal monitored is independ-
ent of the position of the corresponding channel fader.
When monitoring an input channel, the optimum
moment for fading in the corresponding audio source
can be selected.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
1) Connect stereo headphones (impedance ≥ 8 Ω) to
2) Select the channel CH 1 or CH 2 with the selector
3) Adjust the desired headphone volume with the con-
5.3 Announcements via the DJ microphone
To improve the audibility of a microphone announce-
ment, the levels of the channels CH 1 and CH 2 can be
attenuated by 15 dB. For this purpose, press the
switch TALKOVER (3) [LED above the switch lights
up]. If the switch is not pressed, the talkover function is
deactivated.
6 Specifications
Inputs
1 x Mic, mono: . . . . . . . . . . . 1 mV
2 x Phono, stereo: . . . . . . . . 2.5 mV
2 x Line, stereo: . . . . . . . . . . 150 mV
Outputs
1 x Amp, stereo: . . . . . . . . . . 1 V/600 Ω
1 x Record, stereo: . . . . . . . 320 mV/600 Ω
General
Frequency range: . . . . . . . . . 20 to 20 000 Hz
THD . . . . . . . . . . . . . . . . . . . < 0.1 %
S/N ratio, unweighted
Talkover: . . . . . . . . . . . . . . . -15 dB
Headphone output: . . . . . . . ≥ 8 Ω, stereo
Power supply: . . . . . . . . . . . 12 V~/1 A via supplied
Ambient temperature: . . . . . 0 – 40 °C
Dimensions (W x H x D): . . . 165 x 70 x 200 mm
Weight: . . . . . . . . . . . . . . . . . 1.2 kg
Connections
Mic: . . . . . . . . . . . . . . . . . . . 1 x 6.3 mm jack
Headphones: . . . . . . . . . . . . 1 x 6.3 mm jack
All other audio connections: . 12 x phono
Power supply: . . . . . . . . . . . low-voltage jack
According to the manufacturer.
Subject to technical modification.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
the jack PHONES (11).
switch PFL (4).
trol PFL LEVEL (6).
Line: . . . . . . . . . . . . . . . . . 63 dB
Phono: . . . . . . . . . . . . . . . 56 dB
Mic: . . . . . . . . . . . . . . . . . 46 dB
plug-transformer
(230 V~/50 Hz/10 VA)
GB
7