Ritter ESM 50 Instrucciones De Montaje página 20

English
C
To switch it on, first press and
hold down the unlock button (7).
Then, within 2 seconds, press the
power button (8).
• Keep the unlock button
pressed during operation.
The hand blender begins to oper-
ate at the highest speed setting.
The LEDs on the LED display (6)
light up (the number that light up
depends on the current battery
level).
Info:
To prevent the hand blender
from overloading, the appliance
will switch off automatically if it
becomes overheated, if a blade
becomes jammed or if the appli-
ance is operated continuously
for more than 4 minutes. After
it switches off, all LEDs flash
slowly. You can then switch the
blender on again and continue
using it.
• Briefly press the power button
again to adjust the speed if
necessary.
This reduces the speed.
Info :
The next speed setting after
the lowest speed setting is the
highest speed setting.
• Release the unlock button to
switch the appliance off.
Displaying the current battery
level
• Briefly press the unlock
button (7).
The number of LEDs that light up
indicates the current battery level.
14
CLEANING
CAUTION, risk of injury:
– Keep your fingers away from
the buttons to prevent the
appliance from switching on
accidentally.
– The blades on the attach-
ments are very sharp! Never
touch these blades with your
bare hands.
To prevent the accumulation
of food residue, clean the
blender (1) thoroughly after each
use:
• Immerse the blender shaft (3)
of the hand blender in the blender
cup (14) or another container
filled with warm water and
detergent.
• Switch the hand blender on.
Allow it to operate for a short
period in the detergent solution.
• Fill the blender cup or con-
tainer with clean, clear water and
allow the hand blender to operate
in the water for a short period.
• To ensure that all food residue
is removed, detach the blender
attachment (see "Connecting/
replacing an attachment") and
clean it.
• Use a damp cloth to wipe
down the motor unit (2), blender
shaft and charging station (13) if
necessary.
NOTE, Risk of damage to the
hand blender:
– Do not use any scouring
agents, abrasive cleansers,
sponges with rough surfaces
or hard brushes.
– The hand blender is not
suitable for washing in a
dishwasher.
– Do not leave the blender
shaft (3) sitting in liquid for a
long time, as this may cause
discolouration.
• Dry all parts that you have
washed.
CHARGING THE BATTERY
If the blender (1) is switched on,
the number of LEDs that light up
on the LED display (6) indicates
the current battery level. LED 1
flashes slowly to indicate that the
battery is dead.
Info:
Do not switch the blender on if
the battery is dead. Otherwise,
the battery may be damaged.
A
Place the contact surfaces of
the hand blender onto the contact
pin of the charging station (13).
L
When in the correct posi-
tion, the hand blender will feel
securely locked into place and
the LEDs on the LED display (6)
will flash. The number of flashing
LEDs indicates the current bat-
tery level.
Once the battery is fully loaded,
all LEDs go out.
STORAGE
Keep the appliance and the
accessories out of the reach of
children. If storing the appli-
ance for a longer period of time
(without use), ensure that the
battery is fully charged first
(see "CHARGING THE BAT-
TERY"). Otherwise, the battery
may be damaged.
L
The attachments can be
stored on the pins provided on
the charging station.
CHANGING THE BATTERY
CAUTION, risk of injury:
Keep your fingers away from
the buttons to prevent the
appliance from switching on
accidentally.
If LED 1 flashes briefly, this indi-
cates that the battery is defective
(see "Overview of LED dis-
play (6)") and must be replaced:
• Remove the hand blender (1)
from the charging station (13).