Fuel Safety; Safety Instructions For Maintenance; Assembly; To Connect The Throttle Cable And Stop Switch Wires - Husqvarna 333R Mark II Manual De Usuario

Fuel safety

• Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry. Remove unwanted fuel from the
product.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use a soap and water to
remove the fuel.
• Do not start the engine if you spill oil or fuel on the
product or on your body.
• Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
• Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
• Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
• Do not smoke near the fuel or the engine.
• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
WARNING: Read the safety chapter before
you assemble the product.
To install the main body
1. Connect the engine (A) to the tube (B) with four
screws (C). (Fig. 27)
To install the handlebar and throttle
1. Install the handlebar in the handlebar clamp on the
shaft. (Fig. 28)
2. Install the top part of the handlebar clamp onto the
handlebar. Make sure that the clamp is installed onto
the knurling area of the handlebar. Refer to the
illustration.
3. Put on the harness and hang the product from the
support hook.
4. Make a last adjustment to make sure the product is
in a comfortable position when it hangs from the
harness. (Fig. 29)
5. Tighten the screws.
1542 - 002 - 17.07.2020
• Tighten the fuel tank cap carefully or a fire can
occur.
• Move the product at a minimum of 3 m (10 ft) from
the position where you filled the tank before a start.
• Do not put too much fuel in the fuel tank.
• Make sure that a leak cannot occur when you move
the product or fuel container.
• Do not put the product or a fuel container where
there is an open flame, spark or pilot light. Make
sure that the storage area does not contain an open
flame.
• Only use approved containers when you move the
fuel or put the fuel into storage.
• Empty the fuel tank before long-term storage. Obey
the local law on where to dispose fuel.
• Clean the product before long-term storage.
• Remove the spark plug cable before you put the
product into storage to make sure that the engine
does not start accidentally.

Safety instructions for maintenance

• If you cannot adjust the idle speed to make the
cutting attachment stop, speak to your service
center. Do not use the product until the product is
correctly adjusted or repaired.

Assembly

To connect the throttle cable and stop
switch wires
1. Remove the air filter cover.
2. Install the throttle cable (A) through the carburettor
bracket (B). (Fig. 30)
3. Turn the cable adjuster sleeve (C) into the
carburettor bracket fully.
4. Put the slot fitting (D) on the carburettor. At this time,
the recessed hole (E) for the cable lug (F) is away
from the cable adjuster sleeve (C). (Fig. 31)
5. Rotate the carburettor throttle cam and move the
throttle cable (A) through the slot in the slot fitting.
6. Make sure the cable lug (F) drops into the recessed
hole.
7. Operate the throttle trigger some times to make sure
that it operates correctly.
8. Adjust the cable adjuster sleeve (C).
a) Make sure the stop on the carburettor throttle
cam touches the throttle stop correctly.
b) Make sure the cable position keeps 1-2 mm
between cable lug (F) and slot fitting when the
throttle trigger is fully pushed. (Fig. 32)
9. When the throttle cable (A) is adjusted correctly,
tighten the locknut (G).
11