Malfunctions: Causes And Possible Remedies; Malos Funcionamientos, Causas Y Remedios Posibles; Funcionamiento - Accu turn 730 PRO Manual De Instrucciones

Desmonta-neumaticos
Tabla de contenido

MALFUNCTIONS: CAUSES AND POSSIBLE REMEDIES

Malfunction
The chuck does not rotate in
1.
Electrical
any direction
inserted
2.
Incorrect connection of
the plug
3.
Incorrect voltage
When the inverter pedal A is
1.
Polarity inverted
pressed down the chuck
turns anticlockwise
The chuck turns with
1.
Incorrect supply voltage
insufficient force
2.
Slack drive belt
The chuck does not lock the
1.
The pneumatic circuit is
wheel correctly
not connected to the
machine
2.
Insufficient pressure in
the pneumatic circuit
3.
Pressure reducer closed
or wrongly adjusted (for
versions with this device)
The machine (bead-
1.
The unit motor is not
breaker arm or mobile
turning in the correct
chuck) do not make any
direction
hydraulic movements
2.
The thermo-magnetic
circuit breaker is
triggered
3.
A fuse has blown in the
24V circuit
Other possible malfunctions are principally technical in nature and must be checked and resolved by PROFESSIONALLY QUALIFIED TECHNI-
CIANS.
ENGLISH
causes
possible solutions
plug
not
1.
Check that the plug is
correctly inserted and
connected
2-3 (see 1.)
1.
Invert the 2 phases in
the electrical plug
1.
Check that the supply
voltage is the same as
that indicated on the
machine registration
plate
2.
Adjust the belt tightener
1.
Connect the pneumatic
supply
2.
Adjust the supply
pressure correctly
3.
Open or correct the
adjustment of the
pressure regulator
1.
Invert phases 1-2 in the
power supply plug
2.
Reset the thermo-
magnetic circuit breaker
3.
Replace the fuse

MALOS FUNCIONAMIENTOS, CAUSAS Y REMEDIOS POSIBLES

Problemas de

funcionamiento

El autocentrante no gira en
ninguna dirección
Al pisar el pedal de inversión
A, el autocentrante gira en
sentido contrario a las
agujas del reloj
El autocentrante no gira con
suficiente fuerza
El autocentrante no
inmoviliza correctamente la
rueda
La máquina (brazo
destalonador o
autocentrante móvil) no
efectúa ningún movimiento
hidráulico
Otro eventual mal funcionamiento ha de considerarse de carácter únicamente técnico, por lo tanto es el PERSONAL CUALIFICADO
PROFESIONALMENTE que debe intervenir con controles y correcciones.
COD. 104064 Rev.0
ESPAÑOL
Causas
Posibles soluciones
1.
Clavija de tensión no
1.
Controlar que la clavija
enchufada.
haya sido introducida
2.
La
clavija
no
está
correctamente en el
conectada
enchufe. Controlar que
correctamente.
esté bien conectada.
3.
Tensión no conforme.
2-3 (ver 1.)
1.
Polaridades invertidas
1.
Invertir las 2 fases en la
clavija de tensión
1.
Tensión de red
1.
Controlar que la tensión
incorrecta
de alimentación sea
2.
Correa floja
conforme a la indicada
por el fabricante en la
placa
2.
Usar el tensor de correas
1.
La red neumática no
1.
Conectar a la red
está conectada a la
neumática
máquina
2.
Regular
2.
Presión insuficiente de la
convenientemente la
red neumática
presión de la red
3.
Reductor de presión
3.
Abrir o regular
cerrado o mal regulado
correctamente el
(para las versiones con
reductor de presión
dicho dispositivo)
1.
El motor de la central no
1.
Invertir las fases 1-2 en
gira en el sentido
la clavija de tensión
correcto
2.
Activar el
2.
El interruptor
magnetotérmico
magnetotérmico está
3.
Cambiar el fusible
desactivado
3.
Ha saltado un fusible en
la 24V
15
Tabla de contenido
loading

Tabla de contenido