Quick RIDER 1700 W Manual Del Usuario página 15

POS. DESCRIPTION
18 Sensor
19 Rider base
20 Rider barbotin lock pin
21 Regal spring
22 Screw
23 Rope/chain stripper Rider
24 Chain release support
25 Chain release support cam
26 Gypsy lock pin cam
27 Plug
28 Screw
28 Handle
30 Studs
31 Gearbox 2000W
32 Washer
33 Grower
34 Nut
35 Grower
36 Screw
37 Gasket motorgearbox 2000W
38 Key 6x6x30
39 Electric motor 2000W 24V
40 Motor casing watertight 2000W
41 Bottom cover O-ring
42 Bottom cover
43 Lower terminal board gasket
44 Upper terminal board gasket
45 Upper terminal board cover
46 Self-tapping screw M3.9x22
47 Self-tapping screw M3.9x32
48 Gearbox 1700W
49 Washer
50 Self-locking nuts
51 Gasket motorgearbox
52 Key
53 Electri motor 1700W 24V
54 Motor casing watertight 1700W
55 Terminal board gasket
56 Terminal board cover
57 Screw
58 Bottom gasket
59 Bottom cover
60 Cable outlets
61 Magnet
RIDER 1700/2000W - REV001A
CODE
SAKREED00000
SGMSC30C0000
MSVPR2000000
Quick
MMPMS2000000
resistant to marine environments. In any case, any salt
MBV0816MXTSC
deposits on the outside must be removed periodically to
SPMSN20CX000
avoid corrosion and damage to the equipment.
SPMSN20AXS00
The parts where salt may have built up should be washed
MSVCM20S0000
thoroughly with fresh water.
MSVCM20P0000
MBSC04020A00
MBV1040MXTSC Once a year, the drum and the gypsy are to be taken
PVPMESALPA00 apart as follows:
MBP101109X00
MR2000000000
DRUM VERSION
MBR08X000000
Use the handle (1) to loosen the bush (2); pull off the
MBG08X000000
drum (3) and the top clutch cone (10); loosen the fixing
MBD08MXEN000
screws (22) of the chain stripper (23) and remove it. Pull
MBG08X000000
off the gypsy (11).
MBV0825MXE00
PGBMR2000000
NO-DRUM VERSION
MBH0606030X0
Use the handle (1) to remove the gypsy cover (4) and the
EMF202400000
top clutch cone (10); loosen the fixing screws (22) of the
PCCCPM200000
chain stripper (23) and remove it. Pull off the gypsy (11).
PGR035250000
PCCPPMFN2000
Clean all the parts removed to avoid corrosion, and
PCGPMMR2N000
grease the shaft thread (5 or 6) and the gypsy (11) where
PCGPMMR2S000
the clutch cones rest (10 and 12) (use grease suitable for
PCCPPMMR2000
marine environment).
MBV03922AXCC
MBV03932AXCC
Remove any oxide deposits from the terminals of the MR1700000000
electric motor and the solenoid unit; grease them.
MBR10X000000
MBD06MXET000
PGNP10000000
MBH050515F00
EMF172400000
PCCCPM100000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PPM20B000000
PPM20B000000
KPMC08060000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on
the windlass. Carefully remove the chain from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials
GB GB
15 15