Audio Menu; Surr Setup Menu; Surround Fx - Jensen VM9510TS Manual Del Usuario

VM9510TS

AUDIO Menu

The VM9510TS has a built-in Pink Noise generator to help
set the relative speaker levels for multi-channel audio
playback.
Table 13: AUDIO Menu Features
Setting Options Function
Pink Off Stop output of pink noise
Noise
Left Left channel pink noise
Center Center channel pink noise
Right Right channel pink noise
Left Surr Left surround channel pink noise
Right Surr Right surround channel pink noise
Subwoofer Subwoofer pink noise
DRC Off Employ the Dynamic Range Control for
better playback for low volumes.
On
CNTR 5ms Adjust the time difference between the
CTRL center and front speakers to create a
4ms
time delay between 1 and 5 millisec-
onds, producing a more accurate audio
3ms
effect.
2ms
1ms
0ms
REAR 15ms Adjust the time difference between the
CTRL rear and front speakers to create a
12ms
time delay between 3 and 15 millisec-
onds, producing a more accurate audio
9ms
effect.
6ms
3ms
0ms
Down Off Normal Output
Sampling
on Audio signal output at 48kHz
BACK Return to previous menu.
NOTE: When Down Sampling is ON, the audio output
signal will be converted to 48kHz. When Down Sampling
is OFF, the original sampling frequency is preserved.

SURR SETUP Menu

To change speaker settings for 2-channel mode, use the
or buttons (14, 22) on the remote control or the
buttons (18, 19) on the joystick to select "DownMix". To
change speaker settings for 6-channel mode, select "Full
6CH". After selecting 2 or 6-channel mode, use the
(19) on remote control or the button on the joystick (17) to
move to the speaker settings on the right.
Speaker Selection
Selecting LARGE for the multi-channel speaker option will
give a full range output. Selecting SMALL for the multi-
channel speaker option will activate a high pass filter whose
crossover is dependent upon the sub-woofer low pass filter
frequency. For example, if the subwoofer low pass filter is set
to 80Hz, then the high pass SMALL speaker crossover will be
set to 90Hz.
Low pass High pass
80Hz 90Hz
120Hz 135Hz
160Hz 180Hz
Refer to Table 14 when selecting speaker options for each
mode.
Table 14: SURR SETUP Menu Features Setting Options
FL (Front Left) / Large Use when front speakers have
FR (Front Right) good bass output.
Small Use when speakers do not have
good bass output.
19
Table 14: SURR SETUP Menu Features
Setting
LR (Left Rear) /
RR (Right Rear)
SUB (Subwoofer)
CTR (Center)
BACK
or

SURROUND FX

Table 15: SURROUND FX Menu Features
button
Setting
Decode Mode
Panorama
(Only available
when Surround I
Music Mode is
activated.)
Dimension Ctrl
Center Width Ctrl
BACK
Function
NOTE: Surround I is recommended when the playback
source is LPCM (Linear Pulse Code Modulation) or 2-
channel down mixed digital bit-stream.
Options Function
Large Use when rear speakers have
good bass output.
Small Use when rear speakers do not
have good bass output.
None Use when rear speakers are not
present.
Present Use when subwoofer is present.
None Use when subwoofer is not
present.
Large Use when center speaker has
good bass output.
Small Use when center speaker does
not have good bass output.
None Use when center speaker is not
present.
Return to previous menu.
Options Function
Off Play original audio format.
Surround I Use Surround I decoding method.
Surround I Play mono output with surround
Matrix effect.
Surround I Enhance movie surround effects.
Movie
Surround I Play surround music effects.
Music
On Extend the video from the front to
the rear to achieve a better sur-
round effect.
Off Panorama is turned off.
0-6 Shift audio output between front
and rear speakers.
0-6 Shift audio output between front
and center channel speakers.
Return to previous menu.