Detergent And Dishwasher Use; Measuring Out The Detergent; Starting The Dishwasher - Whirlpool ADP 301 Manual De Instrucciones

Detergent and
dishwasher use

Measuring out the detergent

Good washing results also depend on the correct amount of
detergent being used. Exceeding the stated amount does not
result in a more effective wash and increases environmental
pollution.
The amount can be adjusted to the soil level.
In the case of normally soiled items, use approximately either
25g (powder detergent) or 25ml (liquid detergent). If tablets
are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
For good washing results also follow the instructions shown
on the detergent box.
For further questions please ask the detergent producers.
Open the detergent dispenser using button D and measure out
the detergent according to the Table of wash cycles:
Remove detergent residues from the edges of the compartment
and close cover C until it clicks.
The detergent dispenser automatically opens up at the right time
according to the wash cycle.
If all-in-one detergents are used, we recommend using the TAB
option, because it adjusts the cycle so that the best washing and
drying results are always achieved.
Only use detergent which has been specifically designed
for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam residues
remaining in the machine after the cycle has ended.
To achieve the best washing and drying results, the combined
use of detergent, rinse aid liquid and refined salt is required.
We recommend using detergents that do not contain
phosphates or chlorine, as these products are harmful
to the environment.
• powder or liquid: compartments
A (wash detergent) and B (pre-
wash detergent)
• tablet: when the cycle requires
1 tablet, place it in compartment
A and close cover C; when it
requires 2 tablets, place the
second tablet on the bottom of
the appliance.

Starting the dishwasher

1. Press ON-OFF button.
2. Open the door and measure out the detergent. (see detergent
information).
3. Load the racks (see Loading the racks) and shut the door.
4. Select the wash cycle in accordance with the type of crockery
and its soil level (see table of wash cycles) by pressing the P
button.
5. Select the wash options (see Special wash cycles and options) .
6. Start the wash cycle by pressing the START/PAUSE button.
7. The end of the wash cycle is indicated by beeps and the
display shows END. Switch off the appliance by pressing the
ON/OFF button.
8. Wait for a few minutes before removing the crockery, in order
to avoid burns. Unload the racks, beginning with the lower level.
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electricity
consumption.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection process,
it is possible to change the cycle, provided that it has only just
begun: in order to change the wash cycle switch off the machine
by pressing and holding the ON/OFF button. Switch the machine
back on using the ON/OFF button and select the new wash cycle
and any options desired; start the cycle by pressing the START/
PAUSE button.
Adding extra crockery
Without switching off the machine, open the door, taking care
to avoid the escaping steam, and place the crockery inside the
dishwasher. Shut the door and press the START/PAUSE button
the cycle will begin from the point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. once the door has been shut or the electricity
supply is restored, to start again the cycle from where it was
interrupted, press the START/PAUSE button.
23