Display Mode (Menu Option 3, Level 1); Error Display (Menu Option 4, Level 1); Unit Settings (Menu Option 5, Level 1) - Pfannenberg Multi-Controller Manual De Instrucciones De Servicio

Sequence
Selection of menu option 'Load setpoints' in menu
Action
level 2 with the „ " (5) and „ " (6) buttons
Flashing display [LSP] (load setpoints)
Display
Confirmation of the menu option [LSP] with the 'SE
Action
LECT' button (4)
Display [LSP] for 4 sec.
Display
Acceptance of the parameters and automatic re-
Behaviour
turn to normal mode.
ATTENTION!
The parameters which have been set are only accep-
ted when the values which have been set are confir-
med with menu option 'Load setpoints' (menu level
2). If these values are not confirmed, then the old
operational parameters are retained even after a
power outage.

3.3. Display mode (menu option 3, level 1)

Using this menu option, the display mode can be modified. There
are 3 menu options in level 2 available that cause the following
displays in normal mode:
TS1/TS2 alternating
The values from temperature sensors TS1 and TS2 are display-
ed alternately (15 sec.) (only available when a second sensor is
present).
TS1 permanent
The temperature value from sensor TS1 is permanently displayed.
TS2 permanent
The temperature value from sensor TS2 is permanently display-
ed (only possible when a second sensor is present).
The selected setting is reset to the standard value after a power
outage (TS1/TS2 alternating with 2 sensors , or TS1 with only 1
sensor connected).
Sequence
Operational display
Display
Menu activation by pressing the 'MODE' button (3)
Action
for 4 sec.
Display [tES] (test mode)
Display
Selection of menu option 'Display mode' in menu
Action
level 1 with the „ " (5) and „ " (6) buttons
Display [dIS] (display mode)
Display
Confirmation of the menu option [dIS] with the 'SE
Action
LECT' button (4)
Flashing display [tS ] (TS1/TS2 alternating)
Display
Selection of the setting in menu level 2 with the
Action
„ " (5) and „ " (6) buttons
Confirmation of the menu option in level 2 with the
Action
'SELECT' button (4)
New display mode for 4 sec.
Display
automatic return to menu level 2 „TS1/TS2 altern."
Behaviour

3.4. Error display (menu option 4, level 1)

This menu option allows the errors having occurred to the present
to be called up, grouped according to application and unit errors.
Errors are classified according to Table 3.
For each error type, a maximum of 30 errors is stored in a rolling
memory. If the memory limit is exceeded, the oldest errors are
deleted.
Errors numbers and their meanings are listed in Table 3. If an error
has occurred, the 'POWER' operational display (7) also flashes.
Sequence
Operational display
Display
Menu activation by pressing the 'MODE' button (3)
Action
for 4 sec.
Display [tES] (test mode)
Display
10
Selection of menu option 'Error display' in menu
Action
level 1 with the „ " (5) and „ " (6) buttons
Display [Err] (error display)
Display
Confirmation of the menu option [Err] with the
Action
'SELECT' button (4)
Display [E A] (application error)
Display
Selection of the error type in menu level 2 with the
Action
„ " (5) and „ " (6) buttons
Confirmation of the error type from level 2 with the
Action
'SELECT' button (4)
Most recent error of the type, or else if no error
Display
has occurred: [End], the most recent error flashes.
Search the error list with the „ " (5) and „ " (6)
Action
buttons
Return to the menu level above with the 'MODE'
Action
button (3)

3.5. Unit settings (menu option 5, level 1)

This menu option allows the default factory settings to be recalled
(see technical data sheet), the unit of measure for the temperature
display to be changed, and the firmware version to be read off.
The setting of the unit of measure for the temperature is stored in a
non-volatile memory and is retained even after a power outage.
Default factory settings sequence
ATTENTION!
When the menu option 'Default factory settings' is
selected, all previous parameter settings are rendered
null and void.
Operational display
Display
Menu activation by pressing the 'MODE' button (3)
Action
for 4 sec.
Display [tES] (test mode)
Display
Selection of menu option 'Unit settings' in menu le
Action
vel 1 with the „ " (5) and „ " (6) buttons
Display [U S] (Unit settings)
Display
Confirmation of the menu option [U S] with the
Action
'SELECT' button (4)
Flashing display [F S] (Factory settings)
Display
Return to the default factory settings with the
Action
'SELECT' button (4)
[F S] (Execution of the factory settings) for 4 sec.
Display
Return to the default factory settings and auto-
Behaviour
matic return to normal mode.
Sequence for changing unit of measure display for temperature
sensor
Operational display
Display
Menu activation by pressing the 'MODE' button (3)
Action
for 4 sec.
Display [tES] (test mode)
Display
Selection of menu option 'Unit settings' in menu
Action
level 1 with the „ " (5) and „ " (6) buttons
Display [U S] (Unit settings)
Display
Confirmation of the menu option [U S] with the
Action
'SELECT' button (4)
Flashing display [F S] (Factory settings)
Display
Selection of menu option [C F] in menu level 2 with
Action
the „ " (5) and „ " (6) buttons
Display [C F] (Unit of measure settings)
Display
Confirmation of the menu option [C F] with the
Action
'SELECT' button (4)
Flashing display [ºC]
Display
Selection of desired unit of measure in menu level
Action
3 with the „ " (5) and „ " (6) buttons
Confirmation of the new unit of measure from level
Action
3 with the 'SELECT' button (4)
Newly set unit of measure for 4 sec.
Display
automatic return to previous menu option
Behaviour
085 505 518b