Makita SA7000C Manual De Instrucciones página 4

ENGLISH
(Original instructions)
1 Shaft lock
2 Lock button
3 Switch trigger
4 Speed adjusting dial
5 Lock nut
SPECIFICATIONS
Model
Disc diameter ...................................................... 180 mm
Spindle thread ........................................................... M14
No load speed (n ) / Rated speed (n) .........4,000 (min
0
Overall length ...................................................... 453 mm
Net weight .............................................................. 3.4 kg
Safety class ................................................................ /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastic and metal materials as well as painted sur-
faces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
DISK SANDER SAFETY WARNINGS
Safety Warnings Common for Sanding Operation:
1. This power tool is intended to function as a
sander. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as grinding, wire brushing, pol-
ishing or cutting-off are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4
Explanation of general view
6 Abrasive disc
7 Rubber pad
8 Lock nut wrench
9 Exhaust vent
10 Inhalation vent
4.
SA7000C
–1 5.
)
6.
ENE052-1
7.
ENF002-2
8.
GEA010-1
GEB036-5
9.
10. Position the cord clear of the spinning acces-
11. Never lay the power tool down until the acces-
12. Do not run the power tool while carrying it at
11 Commutator
12 Insulating tip
13 Carbon brush
14 Screwdriver
15 Brush holder cap
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
Threaded mounting of accessories must match
the tool spindle thread.
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each
use inspect the accessory such as backing pad
for cracks, tear or excess wear. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during
this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of opera-
tion.
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled into
the spinning accessory.
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
For accessories