The fixing screw must be fixed firmly.
CARBEST VanVent | 318028/318029
4.Remove the upper part of the PLUS FAN top cover, align it with the body fixing plate
frame, and insert the upper part into the frame. After pressing, apply an appropriate
amount of sealant (recommended to use MS type sealant) to (PT4.0 × 12 (4)), and then
use screws to fix the upper part of the body fixing plate.
Mounting of PLUS Fan
5.Arrange the outgoing wires of the upper assembly of the top cover of PLUS FAN . There
are altogether 3 kinds of wiring terminals (1#/2#/3#female ends).
The side fixing screws must be fixed after tightening; otherwise there will be a gap between
the adhesive tape between the upper assembly and the body fixing plate, probably causing
Sidans fästskruvar måste fixeras efter åtdragning, annars
water leakage. (Recommended screw torque: 0.7 N.m)
kommer det att finnas ett mellanrum mellan tejpen mellan
14
utomhusenheten och monteringsramen, vilket troligen
Mounting of PLUS Fan
orsakar vattenläckage. (Rekommenderat skruvmoment:
0,7 N.m)
5.Arrange the outgoing wires of the upper assembly of the top cover of PLUS FAN . There
are altogether 3 kinds of wiring terminals (1#/2#/3#female ends).
Fan motor wire: (Green, blue and yellow) 3P male end 1#;
Lifting motor wire: (Red and black) 2P male terminal 2 #,
(green, orange and yellow) 3P male terminal 3 #;
Vehicle power cord: (Red and black) bare wire;
6.Arrange the outgoing wires of the lower assembly of the interior trim frame of PLUS
FAN , and respectively use 3 kinds of wiring terminals (1#/2#/3#male ends).
Fan motor wire: (Green, blue and yellow) 3P male end 1#;
Lifting motor wire: (Red and black) 2P male terminal 2 #,
(green, orange and yellow) 3P male terminal 3 #;
Vehicle power cord: (Red and black) bare wire;
6.Arrange the outgoing wires of the lower assembly of the interior trim frame of PLUS
FAN , and respectively use 3 kinds of wiring terminals (1#/2#/3#male ends).
Fan motor wire: (Green, blue and yellow) 3P female end 1#;
Ledningsnätet skall vara rent och fritt från skador och
Lifting motor wire: (Red and black) 2P female terminal 2#,
lindningar. Terminalerna ska vara ordentligt anslutna och
(green, orange and yellow) 3P female terminal 3#;
stiften ska vara fria från skador.
Fan motor wire: (Green, blue and yellow) 3P female end 1#;
Input power wire of ventilating fan: (Red and black) bare wire;
Lifting motor wire: (Red and black) 2P female terminal 2#,
(green, orange and yellow) 3P female terminal 3#;
The harness shall be clean, and free from damage and winding. The terminals shall be firmly
Input power wire of ventilating fan: (Red and black) bare wire;
connected and the pins shall be free from any damage.
The harness shall be clean, and free from damage and winding. The terminals shall be firmly
connected and the pins shall be free from any damage.
1
2 12 V
91
4.
Placera VanVent utomhusenhet
på monteringsramen. När du
har tryckt in den, applicera en
lämplig mängd tätningsmedel
(DEKAseal 8936 rekommen-
deras) på skruvhålen och
använd skruvar (PT4.0x12 (4))
för att ansluta de två delarna.
5.
1 VanVent har 3 typer av
anslutningar:
Kabel för fläktmotor:
- (grön, blå och gul)
Kabel för lyftmotor:
- (Röd och svart)
- (Grön, orange och gul)
2 Fordonets nätkabel 12V
(röd och svart) blank tråd;
15
15
DE
EN
IT
ES
FR
NL
FI
DK
SE
