ProFlow PF-SOF1-SIM Instrucciones De Instalación página 13

PROGRAMMING INSTRUCTIONS -
CONFIGURATION PARAMETERS

Before entering the programming mode, make sure that
the appliance is in the service mode.

All configuration parameters on this appliance have
been pre-programmed in the factory, to offer optimal
performance in a wide range of applications and situations.
Nevertheless it may be necessary or desirable to change any
of these parameters, to further optimize the appliances
performance or to adapt it to the specific requirements of
the installation.

In case no button is pressed in a period of 5 min, the
control panel will automatically return to the service mode; any changes made will NOT be saved!
only for PF-SOF1-SIM & PF-SOF1,5-SIM
1. Press the scroll button and hold it for 6 sec until the
display shows:
System Check
2. Within 10 sec, press the up
show:
Units:Metric
 Press the up or down
measure (Metric or US).
3. Press the scroll button again; the display will show:
MaintInt: 24mths
Press the up or down

maintenance reminder function by setting the
maintenance interval, or deactivate the maintenance
reminder function.
4. Press the scroll button again; the display will show:
ExCap:5.5°f M3/L
Press the up or down

exchange capacity per litre of resin.
5. Press the scroll button again; the display will show:
Age corr.:
Press the up or down

correction factor (%/year) to compensate for capacity
loss of the resin due to aging.
6. Press the scroll
button again; the display will show:
Resin:XXX liters
Press the up or down

of resin.
ELECTRONIC CONTROL PANEL
button; the display will
button to set the units of
button to activate the
button to set the
2.0%
button to set the age
button to set the volume
Page 13
7. Press the scroll button again; the display will show:
Override: 7 days
Press the up or down

of days between regenerations.
8. Press the scroll button again; the display will show:
Cycle 1:
Press the up or down

of the regeneration cycle.
Press the scroll button again to advance to the next

regeneration cycle.
Cycle 1 Backwash
Cycle 2 Brine draw/slow rinse
Cycle 3 Fast rinse/brine tank refill (PF-SOF1)
Fast rinse (PF-SOF1,5)
Cycle 4 Brine tank refill (PF-SOF1,5)
9. Press the scroll button again; the display will show:
Regen:Dlyd/Immd
2:00
Press the up or down

regeneration mode:
 Dlyd/Immd: when the remaining capacity equals
the reserve capacity, a delayed regeneration at
the programmed time of regeneration is started;
however when the remaining capacity equals 0
before the programmed time of regeneration is
reached, an immediate regeneration is started.
 Immediate: when the remaining capacity equals
0, an immediate regeneration is started.
Note: Delayed manual regeneration is not
available when this regeneration mode is
selected.
 Delayed: when the remaining capacity equals the
reserve capacity, a delayed regeneration at the
programmed time of regeneration is started.
10. Press the scroll button again; the display will show
(only when the regeneration mode is set to 'Delayed' or
'Dlyd/Immd'):
Regen @
 Press the up or down
regeneration.
11. Press the scroll button again; the display will show
(only when the regeneration mode is set to 'Dlyd' or
'Dlyd/Immd'):
Rsrv Variable
Press the up or down

capacity:
 Variable: the reserve capacity is calculated
automatically, based on the registered daily water
usage.
 Fxd: press the scroll
up or down
capacity to a fixed amount.
button to set the number
XX min
button to set the length
button to set the
2:00
button to set the time of
button to set the reserve
button again and press the
button to set the reserve
EN - English