Logan Graphic Products FoamWerks WC-2001 Instrucciones

www.foamwerks.com
Blade Storage
Drawer
Channel Guide
OPERATING INSTRUCTIONS
Blade Installation
1 Remove the yellow Blade Clip by pushing the clip forward.
2 Place the blade in the blade depression, matching the blade tip with the angle
in the indentation.
3 Replace the Blade Clip, taking care to position the open end of the clip to the
top. Slide upwards until clip snaps into place (
4 Repeat for blade on opposite side.
NOTE: Spare blades can be stored in the Blade Storage Drawer, located on
the back side of the V-Groove Cutter. To open, squeeze the Blade Storage
Drawer equally from left and right with fingers placed on the drawer ridges.
Cutting
NOTE: Always protect tabletop with a scrap piece of foamboard underneath
the board being cut.
1 SAFETY NOTE: Keep fingers clear of the blade area.
2 Using the W-3001 Channel Rail (sold separately, or use the Logan Adapt-A-
Rule or Team System), lightly mark the board to indicate the center of the
desired V-groove.
3 Position the Channel Rail on the foamboard. Hook the Channel Guide onto
the rail. Align the front and back tick marks to the previously marked line (
).
2 & Fig. 3
4 With the blades positioned off the top edge of the foamboard, push the
Cutting Head downward. With Cutting Head fully depressed, pull the V-
Groove Cutter backwards along the Channel Rail and continue along the
length of the foamboard (
Fig. 4
Blade Depth Setting
1 The blades can be raised or lowered in unison by turning the Blade
Adjustment Knob found on the back side of the V-Groove Cutter (
2 Turn the Blade Adjustment Knob to the right to raise the blades, or to the left
to lower the blades. Look at the bottom of the V-Groove Cutter, follow the
directional arrows. The Blade Depth Position Scale provides a rough guide to
the blade depth position (
Fig. 6
NOTE: Test the blade height by doing a test cut on a scrap piece of
foamboard prior to your final cut.
TIP: At some settings, the V-Groove Cutter may cut completely through the
foamboard. If this is NOT the effect you desire, be sure to do a test cut prior
to your final cut. Note that the V-Groove Cutter cannot cut completely
through 1/2" foamboard (1.27cm).
L o g a n G r a p h i c P r o d u c t s I n c . , 1 1 0 0 B r o w n S t r e e t , Wa u c o n d a , I L 6 0 0 8 4 To l l F r e e 1 8 0 0 3 3 1 6 2 3 2 w w w. l o g a n g r a p h i c . c o m
All manuals and user guides at all-guides.com
I N S T R U C T I O N S
V-Groove Cutter
Blade Clip
).
Fig. 1
).
).
Model WC-2001
Blade Depth
Adjustment Knob
Cutting Head
Fig. 1
Fig. 3
Fig.
).
Fig. 5
Fig. 5
1/16" to 3/4"
(0.16cm to 1.9cm)
CAUTION: BLADES EXTREMELY SHARP
Use replacement blades #WC-10, WC-25 or WC-100
Blade Storage Drawer - Located on the
rear of the tool, used to store extra blades
Channel Guide - Clips onto Channel Rail
(W-3001) to create accurate, straight cuts
Blade Clip - Used to hold blade in place
Cutting Head - Flexible head that holds
blades and is depressed to make V-Groove cut
Blade Depth Adjustment Knob - Raises
and lowers blades, which varies the total
width of the resulting V-groove cut
Fig. 2
Channel Rail
rear tick
alignment
Fig. 4
Blade Depth
Position Scale
Fig. 6
Cuts V-Grooves into foamboard or
cellfoam, with resulting V-grooves 1/16"
to 3/4" wide (0.16cm to 1.9cm).
J1708 9_08
Made in China
front tick
alignment