Technical Data; General Power Tool Safety Warnings - Milwaukee SDS PLUS 5263-59 Manual De Instrucciones

TECHNICAL DATA

Rated input ................................................................................
Output ........................................................................................
Voltage.......................................................................................
No-load speed ...........................................................................
Speed under load max. .............................................................
Rate of percussion under load max. ..........................................
Impact energy per stroke according to EPTA-Procedure 05/2009 ......
Drilling capacity in concrete .......................................................
Drilling capacity in steel .............................................................
Drilling capacity in wood ............................................................
Optimized capacity in concrete/brick .........................................
Chuck neck diameter .................................................................
Weight according EPTA-Procedure 01/2003 .............................
Noise Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .........................................
Sound power level (K = 3 dB(A)) .............................................
Wear ear protectors!
vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
Hammer-drilling in concrete: ..................................................
Uncertainty K = ......................................................................
WARNINg
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.

gENERAL POWER TOOL SAFETy WARNINgS

WARNINg! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed
or grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
:
h
5263-59 / 5263-59A
..................... 620 W ........................... 620 W
..................... 310 W ........................... 310 W
220-240 V~ 50-60Hz ............127V~ 50-60Hz
............ 0-3700 min
-1 ...............................
............ 0-2700 min .................. 0-2700 min
-1
............ 0-4400 min .................. 0-4400 min
-1
........................ 2,0 J .............................. 2,0 J
.....................20 mm ...........................20 mm
.....................13 mm ...........................13 mm
.....................30 mm ...........................30 mm
..................5-12 mm ........................5-12 mm
.....................43 mm ...........................43 mm
...................... 1,9 kg ............................ 1,9 kg
.................90 dB (A) .......................90 dB (A)
...............101 dB (A) .....................101 dB (A)
....................12 m/s ..........................12 m/s
2
...................1,5 m/s .........................1,5 m/s
2
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
5263-59B
0-3700 min
-1
-1
-1
2
2
21