Westward 23NY36 Instrucción De Servicio

Teniendo separador/ juego de extractores
Idiomas disponibles

Idiomas disponibles

Operating Instructions Manual
Please read and save these instructions. Read through this owner's manual carefully before using product. Protect
yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could
result in personal injury and/or damage to product or property. Please retain instructions for future reference.
Description
Pulling bearings off shaft and separating bearing housings
Unpacking
When unpacking, make sure that the product is intact and
undamaged.
After unpacking unit, inspect carefully for any
damage that may have occurred during transit. Check for
loose, missing, or damaged parts. Shipping damage claim
must be filed with carrier.
Specifications and Dimensions
Model
Type
23NY36
Manual
General Safety Information
Inspect the contents before every use; do not use if
parts are missing, loose or damaged. Always pay
close attention to what you are doing when using this
tool set. Only use the tool for it's intended use. Do
not assemble the tool when tired or taking medication
which would cause drowsiness.
Improper assembly can create hazards to users. To
avoid personal injury, always wear ANS and OSHA
approved safety goggles during assembly. Before
using the tool, keep assembly area clean, well lit, and
keep bystanders out of area during assembly.
To help avoid personal injury or
equipment damages, assemble this tool set
according to these instructions.
Read this material before using
this product. Failure to do so can result in serious
injury. SAVE THIS MANUAL.
Assembly
SEPARATING BEARING HOUSINGS
a.
Select the proper size bearing separator jaw for
the bearing size being separated.
WEM-23NY3601
Printed in TAIWAN
07/13
Number of
Capacity
Jaws
(Tons)
2
5 Ton
Bearing Separator / Puller Set
Jaw Reach
Jaw Spread (In.)
(In.)
1-5/8
2-5/8 to 3-3/8
b.
Loosen the separator jaw nuts enough to allow
the jaws to hold between each bearing.
c.
Use a wrench (not included in the tool set) to
tighten the nuts on the side until the jaws are
tightly secured in between the bearing housings.
d.
Select a pair of proper size extension screws and
assemble into the jaws.
e.
The extension screws allow the user to grip them
and add stability while tightening nuts.
f.
Continue tightening the nuts until the bearing
housings are separated.
g.
When the bearing housings are separated,
remove the bearing separator jaw.
NOTE: Do not over tighten the nuts because it may
damage the bearings.
PULLING THE BEARINGS OFF THE SHAFT
a.
Select the proper size bearing separator jaw for
the bearing size being removed from the shaft.
b.
Loosen the separator jaw nuts enough to allow
the jaws to hold between each bearing.
c.
Use a wrench (not included in the tool set) to
tighten the nuts on the side until the jaws are
tightly secured in between the bearing housings.
23NY36
Jaw Style
Puller Jaw
Tabla de contenido
loading

Resumen de contenidos para Westward 23NY36

  • Página 5: Teniendo Separador / Juego De Extractores

    Instrucción de servicio 23NY36 Por favor, lea y guarde estas instrucciones. Lea este manual de instrucciones cuidadosamente antes de usar el producto. Protéjase a sí mismo ya los demás observando toda la información de seguridad, advertencias y precauciones. El incumplimiento de las instrucciones podría resultar en lesiones personales y / o daños al producto oa la propiedad .
  • Página 6: Mantenimiento

    Westward Operating Instructions and Parts Manual 23NY36 Bearing Separator / Puller Set Con una llave (no incluido) para girar el tornillo NOTA: No apriete demasiado las tuercas, ya que en sentido horario hasta forzar la caja del puede dañar los cojinetes.
  • Página 7 Por favor proporcione la siguiente Número de modelo Número de serie (en su caso) Descripción de las partes y el número que se muestra en la lista de piezas Figura A - Reparación de piezas de ilustración para el modelo (s) 23NY36...
  • Página 8 Westward Operating Instructions and Parts Manual 23NY36 Bearing Separator / Puller Set Lista de Repuestos (esto debe incluir cada parte hace referencia en la ilustración de las piezas) Número de Referencia Descripción Qty. Tornillo (1/2” – 20) 2.2” ~ 3” Separador Jaw Bearing Tuerca (1/2”...

Tabla de contenido