Idiomas disponibles
Idiomas disponibles
1. Tidy cables and loose items from the
ground and move any unstable, fragile,
precious, or dangerous items to prevent
personal injury or property damage due to
items becoming tangled in, struck by, or
knocked over by the robot.
2. When using the robot in a raised area,
always use a secure physical barrier to
prevent accidental falls that may result in
personal injury or property damage.
Note:
When using the robot for the first time, follow it
throughout its whole cleaning route and watch for potential
problems. The robot will be able to clean by itself in future uses.
Position the Charging
B1
Dock
Keep the Charging Dock on a level surface,
flat against a wall. Connect the power cable to
the Charging Dock and tidy cables from the
floor. To ensure a better user experience of
the mobile app, place the Charging Dock in
an area with good WiFi coverage.
B1-1 More than 0.5m (1.6ft)
B1-2 More than 1.5m (4.9ft)
Notes:
• Allow at least 0.5m (1.6ft) of clearance on each side, and
more than 1.5m (4.9ft) in front of the charging dock.
• If the power cable hangs vertical to the ground, it may
be caught by the robot, causing the charging dock to be
disconnected.
• The charging dock indicator is on when the charging dock is
electrified, and off when the robot is charging.
• Do not place the charging dock in places that are directly
exposed to sunlight, or block the location beacon. Otherwise
the robot may not be able to automatically return to the
charging dock.
Secure the charging dock
B2
with the adhesive tape
Wipe the floor of the area where the
charging dock will be placed with a dry cloth,
then secure the dock in place using double-
sided tape at the bottom of the dock.
Note: When necessary, remove the double-sided adhesive
tape slowly to reduce residue glue.
Attach the Moisture-Proof
B3
Mat
After fixing the charging dock in place, use
a dry cloth to clean the area where the
Moisture-Proof Mat will be located. Tear off
the double-sided tape at the bottom of the
Moisture-Proof Mat, and stick the mat on
the floor .
Notes:
• Always place the Moisture-Proof Mat on wooden floors.
• The Moisture-Proof Mat attaches best to smooth surfaces.
• When necessary, remove the double-sided adhesive tape
slowly to reduce residue glue.
Power on and charge the
robot
Press and hold the
button to power on
the robot. When the power light goes on,
place the robot on the dock to charge. Make
sure the charging dock power indicator
turns off and a "charging" voice alert sounds.
To maintain the performance of the high-
performance lithium-ion rechargeable battery
pack, keep the robot charged.
08
Note:
The robot may not turn on when the battery is low. In
this case, place the robot directly onto the dock to charge.
Mopping
B4
To prevent excessive dirt buildup during first-time
Note:
use, floors should be vacuumed at least three times before
mopping.
B4-1—Press the latch and slide the
dustbin and water tank combo unit
backwards.
B4-2—Fill the water tank
Remove the water tank stopper, fill the tank
with water, and close it tightly.
Notes:
• To prevent corrosion or damage, only use the Roborock
branded floor cleaner in the water tank.
• Do not use hot water as this may cause the tank to deform.
• When filling the water tank, tilt tank 30° to avoid wetting
the filter.
B4-3—Reinstall the dustbin and water
tank combo unit
Slide the water tank into the robot until you
hear it lock with a click.
B4-4—Install the mop cloth
Wet the mop cloth and wring it until it stops
dripping, then slide it along the mop cloth
slot before sticking it firmly in place.
Only use the official Roborock mop cloth.
Note:
B4-5—Install the mop cloth mount
Slide the mount forwards along the bottom
of robot until it clicks in place.
Note:
Clean the mop cloth after 60 minutes of mopping to
maintain water flow and cleaning quality.
B4-6—Remove the mop cloth mount
