Worx WX876 Manual página 12

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 51
ASSEMBLY AND OPERATION
ACTION
BEFORE OPERATION
Charging the detachable batteries.
Connect the cooler to the DC/AC power
supply, then put the batteries into the
battery case, finally the batteries will be
charged randomly.
You can also charge the batteries with a
Worx PowerShare Charger .
Note:
1. The batteries will be charged more
quickly if just switch off the cooler
when charging, as the power supply will
mainly power the compressor instead
of batteries when the cooler is running.
2. The batteries will be charged randomly.
OPERATION
-AC Power Mode
Turn on: Plug the AC cord into the cooler
and to a power supply, then the cooler is
ready to work.
Turn off: Long press the ON/OFF button
for 3 seconds until "OFF" shows in the
12
control panel. Remove the power cord.
-Battery Power Mode
Turn on: If batteries already in the battery
pack compartment, remove batteries out
and reinsert the batteries into the slots in
the battery compartment; if no batteries in
the compartment, just put the batteries in
the compartment to turn on.
Turn off: Long press the ON/OFF button
for 3 seconds to power the cooler off.
Note: 1. If the batteries have been left in
the battery compartment and the cooler
is not turning on, remove the batteries and
reinsert them. Also check that the batter-
ies are fully charged.
-Car Mode
Turn on: Plug the cigarette lighter adaptor
into the cooler and to the power supply in
the car to turn it on.
Turn off: Long press the ON/OFF button
for 3 seconds to power the cooler off.
Remove the power cord.
20V Portable Electric Cooler
Exchange the cooling mode
Press the SET switch to choose the suitable
FIGURE
cooling mode MAX(fast-cooling) or ECO(
energy saving)
Note:
1. The factory setting is MAX mode.
Setting the Temperature
Note: Batteries must be installed or cooler
connected to power source to change set-
tings
Setting the Temperature
See Fig.
Turn ON the cooler. Use the +- buttons to
A1,A2
select desired temperature.
Note: Temperature setting range is
-20°C~20°C / -4°F~68°F
Setting the Temperature Unit
Turn the cooler on. Long press +- at the same
time for 3 seconds until E1 is displayed. Then
press the SET button again until E5 is shown.
Press + or - to select Celsius or Fahrenheit.
Note: Factory default is Celsius/°C
Reset Temperature
Turn the cooler on, then Long press +- at the
same time for 3 seconds until E1 is displayed
,then press + or - to reset the tempearture .
Note: The minimum temperature setting is
-20°C / -4°F
Transportation and Moving
It is available to hold the handle, leave the
cooler at a 30
gently to anywhere you need to go.
Note:
1. When used outside, for best cooling
See Fig.
results and extended runtime, pre-cool
B1,B2,B3
the cooler with the AC power supply or
cigarette lighter adaptor. When the cooler
has reached desired temperature, install the
batteries for portable cooling.
2.The cooler can also be used without the
batteries if connected to the AC power
supply or the cigarette lighter adaptor.(see
Fig B1,B3)
BATTERY PROTECTION MODE
In order to prevent the cooler from running down the
car battery, the cooler is equipped with BATTERY
PROTECTION MODE.
How to select BATTERY PROTECTION MODE:
1. When the cooler is running, please press the SET
button for three seconds until screen flashes, then
press SET button again to select protection mode
H(high), M(medium), L(low). Factory setting is H
angle and move the cooler
o
See
Fig. C
See
Fig. D1,
D2,D3
See
Fig. E
EN
loading

Este manual también es adecuado para:

Wx876.x