rotation adjuster 360°; 12.Shoulder belt pads; 13.Shoulder strap; 14.Headrest cushion; 15.Handle for adjusting the backrest
of the seat; 16.ISOFIX system attchments; 17.ISOFIX adjustment button; 18.ISOFIX guide slot; 19. Instruction storage
compartment.
Step 1: Install the guides of ISOFIX attachments to the vehicle's ISOFIX anchorage points, which are located between the
surface and the backrest of the vehicle seat.
Step 2: Press ISOFIX button to release ISOFIX attachments and pull them out (position "longest attachments").
Step 3: Place the child seat on the car seat and direct the two ISOFIX connectors to the ISOFIX anchorage points on the car
seat.
Step 4: Press one of the ISOFIX connectors to engage it to the ISOFIX anchorage point with a 'click'. Repeat on the other side
to secure both ISOFIX connectors. The ISOFIX indicator should be green on both sides. Installation is completed. WARNING!
The ISOFIX connectors are only fitted correctly if both ISOFIX system indicators are marked green.
Step 5: Press the car seat firmly against the backrest of the vehicle seat. Shake the child seat to make sure it is securely
fastened and check the green safety buttons again.
Press the ISOFIX button again to release the lugs from the guides.
The upper anchor point is fixed device on the trunk or the floor of the vehicle.
Press the adjustment button on the top tether to adjust its length. Slide the straps of the top tether through the upper guide
hooks. Pull the upper part of the top tether and press the adjuster to secure the strap to the back of the car seat. The
attachment points of the device are in 3 positions (A/B/C).
adjuster show „green color". If the indicator does not show green, reinstall.
ATTENTION! After installation make sure the car seat is firmly and securely secured (4).
To adjust the head support, pull and hold the head support release handle. Pull the handle up to move the head support to
a higher position. Hold the handle and push the head support down to move it to a lower position. When the head support
is in the desired position, release the handle to lock it.
•
If the child seat is used rear-facing, the head restraint should be adjusted so that the 5-point harness straps are at the
same height or slightly below the child's shoulders.
•
If the child seat is used forward-facing, the head restraint must be adjusted so that the straps of the 5-point harness
are at the same height or slightly above the child's shoulder.
Step 1: Hold down the harness adjustment button and pull the shoulder belt towards you as far as possible. Make sure to
pull the shoulder belt under the chest pads as shown in Figure 1.
Step 2: Press the red button on the 5-point belt buckle to unbuckle it.
Step 3: Put the child to sit in the seat. Slide the shoulder belts over the child's shoulders and tuck the tongues of the buckle
into each other. Lock the tucked tongues into the buckle.
Step 4: Pull both shoulder belts to tighten the lap belt. Make sure the lap belt is positioned low down so that the child's
pelvis firmly gripped.
Step 5: Pull up on the 5-point belt adjuster until the belt secures the child properly. Pull the two chest pads to the lowest
position.
REMOVING THE 5-POINT SAFETY HARNESS
ATTENTION! The 5-point safety harness of car seat must be removed when child reaches height 100-150 cm.
Step 1: Unlock the belt from central buckle, remove the crotch pad and insert the buckle through the slot of fabric cover.
Step 2: Press and hold the button for shoulder belts adjustment. Remove the cover at the back of backrest, pull the metal
joint and split the shoulder belt from it. Place the metal joint into the slots of car seat and tighten it to prevent falling.
Step 3: Lift the cover of head support and pull the shoulder belts at front to remove them.
INSTALLING THE ISOFIX SYSTEM - FIGURE C
INSTALLING THE TOP TETHER - FIGURE D
HEAD SUPPORT ADJUSTMENT - FIGURE E
PUTTING A 5-POINT SAFETY HARNESS- FIGURE F.1
REMOVING THE 5-POINT SAFETY HARNESS- FIGURЕ F.2
THE NEWBORN INLAY - FIGURE G
- FIGURE B.3
- FIGURE B.1
- FIGURE B.3
- FIGURE B.1
Tighten the belt of the top tether, until the indicator of top tether
- FIGURE B.3
- FIGURE B.1
- FIGURE B.3
- FIGURE B.1
26
