Nuna bryn Manual Del Usuario página 8

Product Setup
Check that you have all the parts for this product before
assembling it. The assembly should be performed only
by adults.
Assemble & Detach Rear Leg
1
- Place the bottom of seat facing upwards. (1)
2
- Clip the rear leg into the slot. (2)
3
- A "click" indicates the leg is attached. Pull on the
leg to check. If the leg is attached properly, the tab
on the rear leg will be completely inside the slot.
(3)
4
- Press the release button to remove the rear leg. (4)
Assemble & Detach Front Leg
1
- Clip the front leg into the slot. (5)
2
- Correct installation as shown in Figure (6).
3
- Press the release button to remove the front leg.
(7)
Assemble & Detach Footrest
1
- Open the footrest mount. (8)
2
- Press the releasing button. Clip the footrest
mount into the slot and move both sides up
simultaneously (8).
3
- Correct installation as shown in Figure (11).
Incorrect installation as shown in Figure (9)(10).
4
- The footrest has 3 positions. (12)
5
- Adjust the footrest to the lowest position. Press
the adjustment button and mounts on both sides,
and move down simultaneously to remove the
footrest. (13)
Assemble & Detach Backrest
WARNING The high chair mode must have backrest
installed correctly.
1
- Press the release button to remove the backrest.
(14)
2
- Clip the backrest mount into the slot. (15)
3
- A "click" idicates that it has been installed
correctly. (16)
Assemble & Detach Armbar
1
- Clip the armbar into the slot. (17)
2
- A "click" idicates that it has been installed
correctly. (18)
3
- Press the release button to remove the armbar.
(19)
5 BRYN instructions
Assemble & Detach Tray onto Armbar
WARNING The tray and the armbar alone DO NOT
guarantee the restraint of your child!
1
- Press the release button to install the tray. (20)
2
- A "click" idicates that it has been installed
correctly. (21)
3
- Press the release button to remove the tray. (22)
Product Use - Child Mode
Use Insert
1
- Push the insert through the hole in the seat pad
(23).
2
- Straighten the insert and make sure it lays flat
inside the seat pad so the child can sit comfortably
(24).
Securing Child
1
- Press the button, the buckle will release
automatically. (25)
2
- Place the waist belt buckle close to the female
buckle, and they will automatically adsorb and
lock. (26)
3
- Adjust the length of the webbing to adjust the
waist belt length. (27)
Belts must not be twisted.
4
- The use of high chair mode is shown in Figure (28).
High chair mode requires correct use of safety
buckles.
Product Use - Youth Mode
1
- Slide the harness crotch strap and waist straps out
of the slots in the seat. (Tip: It is easier to do the
waist straps one at a time.) Pull the harness away
from the seat to remove (30).
(29)
2
- Remove the seat pad (31).
3
- Footrest can be adjusted for comfort (32).
When using this product in youth mode, the
harness and seat pad must be removed.
Cleaning and maintenance
You can clean the high chair and accessories with
a damp cloth or a neutral detergent, but do not use
abrasive detergents or solvents which could damage
the material.
Continued and extended exposure to sunlight can
change the colour of many materials.
Inspect your high chair regularly in order to detect any
damage.
Parts List
1 Backrest 8 Tray Release Button
2 Seat 9 Tray
3 Armbar Release Buttons 10 Front Leg Attachment
4 Rear Leg (x2) 11 Footrest Slot
5 Front Leg (x2) 12 Footrest Release Button
6 Footrest 13 Footrest Mount
7 14
Armbar Seat Pad
1
2
3
7
4
5
6
13
9
15 Insert (inside seat pad)
16 Harness
17 Buckle Release Button
18 Adjustment Straps
19 Backrest Mounts
20 Armbar Mount
9
8
14
15
2
16
18
17
6
4
5
10
11
19
20
NUNA International B.V. Nuna and all associated logos are trademarks.
BRYN instructions
12
6