Idiomas disponibles
Idiomas disponibles
into water, do NOT try to pick it up. Unplug it immedia-
tely.
not be used near water.
- Before plugging the appliance into the mains, check
the voltage indicated matches that of your home.
- Connect the appliance to a power socket that
supports at least 10 amps
- The electrical plug on the appliance must match
the power socket. Never modify the plug. Do not use
plug adapters.
-Never pull the cord or use it to hang up the
appliance. Always unplug the appliance by pulling
the connection pin, and not the cord.
- Do not use the appliance if the cable or plug is
damaged.
- Do not coil the mains cable around the appliance.
- Do not allow the power cable to hang off the
table or come into contact with the appliance's hot
surfaces.
- For extra protection we recommend installing
a residual differential current device (RDD) not
exceeding 30mA in the electrical circuit supplying the
bathroom. Ask your installer for advice.
-Do not touch the appliance with wet hands when it
is plugged in.
- Before plugging the appliance into the mains, make
sure your hands and the appliance are completely
dry.
- If any of the appliance's covers break, immediately
unplug the appliance from the mains supply to
prevent the possibility of being electrocuted.
-WARNING: do not use the appliance near water.
- Do not use or store the appliance outdoors.
- For maximum efficiency, the plates reach the
temperature used by professionals (220ºC). Do
not touch the plates or the case covering them, as
they reach very high temperatures. Be sure that the
plates do not touch your eyes or bare skin while
using the appliance.
- While operating, the plates may reach tempe-
ratures of up to 220ºC. The plastic parts near the
ceramic plates may also be hot. We recommend
that you hold the appliance with your hand in the
temperature control zone.
- Never leave the appliance outdoors and exposed
to the elements.
- Under no circumstances should you use flammable
substances (gel, etc.) on your hair before using the
straighteners.
- Never leave the appliance on a wet surface or cloth
while it is plugged in.
- Do not leave the appliance operating on surfaces
Manual slimlook keratin pro.indb 9
This symbol indicates that the appliance should
that are not heat resistant. Be sure that the plates
are cool before placing the appliance on the surface.
- Do not use the appliance if the On/Off device is
not working.
• Always unplug the appliance after use and before
removing or installing parts and before doing any
maintenance or cleaning. Also unplug it in the case
of a power cut. When plugging in or unplugging the
appliance, it must always be turned off.
- This appliance is exclusively for household use,
not for industrial use. Use for any other purpose may
be dangerous.
- Store this appliance out of the reach of children
and/or those with reduced physical, sensory or
mental abilities or unfamiliar with its use
- Do not leave the appliance unattended when
switched on.
-Do not use the appliance on pets or animals.
-If you do not use the appliance for a long period of
time, store it in a dry, safe place away from children.
Common features:
Nanoceramic, turmaline and keratin plates
The Nanoceramic, tourmaline and keratin plates
make hair softer than conventional plates, allowing
the hair to glide through without friction, and protec-
ting it from damage. As the hair glides through, the
cuticle is sealed, eliminating frizz.
Round edged tilting plates: straight and curly hair
This model has tilting plates, and the slight move-
ment allows the plates to adapt to the hair without
exerting pressure or pulling. The plates glide along
the hair easily, smoothly, without pulling. This featu-
re makes it much easier to straighten, wave, curl and
give volume to the hair.
Fast heating
These straighteners have a high-performance
professional element, which makes it ready to use in
just 30 seconds.
Automatic safety cut off
For safety reasons the straighteners will switch
themselves off after 60 minutes if not touched.
Touch control
Easy, convenient touch sensitive temperature control
19/05/15 09:16
