FRAM FreshBreeze CF9846A07 Guia De Inicio Rapido

CF9846A
Installation Bulletin:
Bulletin d'installation :
Boletín de Instalación:
Estimated time of installation:
Temps estimé pour l'installation :
Tiempo estimado de instalación:
Application:
Mazda: MPV | Mitsubishi: Endeavor, Galant |
Application:
Toyota: 4Runner, Celica, FJ Cruiser, Prius, Sienna
Aplicación:
For more application specifics,
please refer to our catalog.
Pour obtenir plus d'information
sur les applications, veuillez
consulter notre catalogue.
Para obtener información
específica sobre la aplicación,
consulte nuestro catálogo.
FRAM Group Operations LLC
Danbury, CT 06810-5109 U.S.A.
©2012 FRAM Group IP LLC
FRAM Group (Canada) Inc.
2430 Meadowpine Blvd.
Unit 105 & 107
Mississauga, ON
L5N 6S2 Canada
SOME VEHICLES MAY DIFFER SLIGHTLY. IF YOU HAVE QUESTIONS
REGARDING THIS FILTER, ITS INSTALLATION OR MORE DETAILS
SPECIFIC TO YOUR VEHICLE, PLEASE VISIT
www.framfreshbreeze.com
FOR HOW-TO VIDEOS AND ADDITIONAL INFORMATION.
CERTAINS VÉHICULES PEUVENT PRÉSENTER DES DIFFÉRENCES. SI VOUS
AVEZ DES QUESTIONS CONCERNANT CE FILTRE, SON INSTALLATION OU
DÉSIREZ OBTENIR PLUS DE DÉTAILS CONCERNANT VOTRE VÉHICULE,
VEUILLEZ VISITER LE www.framfreshbreeze.com POUR OBTENIR
DES DÉMONSTRATIONS VIDÉOS ET PLUS D'INFORMATION.
PUEDE VARIAR UN POCO EN ALGUNOS VEHÍCULOS SI TIENE PREGUNTAS
SOBRE EL FILTRO Y LA INSTALACIÓN O DESEA INFORMACIÓN EN DETALLE
PARA SU VEHÍCULO, VISITE www.framfreshbreeze.com, DONDE
ENCONTRARÁ VIDEOS INSTRUCTIVOS E INFORMACIÓN ADICIONAL.
Importado por:
FRAM Group Operations Mexico City S.A. de C.V. FRAM Group Operations Mexico City S.A. de C.V.
Carretera México-Cuautitlán km 31.5 S/N
Nave 5, Conjunto Industrial Cuautitlán.
Col. Loma Bonita
Cuautitlán, Edo. de México
MEX, C.P. 54800
Tel. 01 800 7154 135
Hecho en China
TOOLS: TOOLS: None required. TOOLS:
LOCATION OF CABIN FILTER: Behind the glove box or inside the glove box.
REMOVE REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION. REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION.
07-10
15 minutes or less
1. Sit in the passenger side seat and open the glove box. (Fig 1)
15 minutes ou moins
15 minutos máx. 2. On the right hand side of the glove box you will see a rod connected to the glove box. This is called the dampener rod.
Remove the arm by slightly closing the glove box while pulling the arm slightly forward and off the shaft it is hooked to. (Fig 2)
3. Next, push in on both sides of the glove box while pulling it downward until you disengage the stops on each side of the glove
box. When you are doing this you will be flexing the glove box until the stops that hold the glove box from opening too far clear
the sides of the glove box frame and this will allow the glove box to swing down on its bottom hinge. (Fig 3)
4. You should now see the cabin filter cover. Remove the cabin filter cover and frame by grabbing the cabin filter cover and
pulling it straight out. The cabin filter frame is attached to the cover and will be removed at the same time. (Fig 4)
5. Remove the old filter from the frame by pushing it up from the underside of the filter frame and removing it from the tabs that
are securing the filter to the frame. (Fig 5)
6. Install the new filter into the frame and insure that the edge of the filter is securely tucked under all the retaining tabs on the
filter frame. (Fig 6)
7. Reinstall the cabin filter frame by sliding it back into the housing until it is seated back into position in the housing and the
cover is secure.
8. Pick up the glove box and swing it upward on the bottom hinge like you are closing it and partially close it until the stops on
each side of the glove box re-engage. You may want to squeeze in on the glove box or push out on the back of the glove box
until the stops clear the sides of the glove box frame if it looks like the stops might damage or scratch the sides
of the glove box frame.
9. Now re-install the dampener rod by sliding it back on the shaft on the glove box.
10. Close the glove box.
1
2
4 5
3
6