Panasonic PanaSync E70 Manual De Instrucciones página 6

Ocultar thumbs Ver también para PanaSync E70:
Idiomas disponibles

Idiomas disponibles

Precautions
1) Installation
Install
the monitor
in
a
well ventilated place.
Avoid exposing
to
direct sunlight,
a
heater,
or
any
other
heat source.
Heat
will
adversely
affect
the
cabinets
and
the
parts
inside.
Position
the display
unit
so
that
the holes
in
the cabinet
will
not
be blocked
during use.
Keep
the display
unit
away
from
the
kitchen,
bathroom,
washing
machine,
or other
sources
of
exposure
to
water,
steam
or moisture.
In
order
to
use
the display
unit safely,
use
only the supplied
AC
Power
cord.
The
AC
Power
cord
must be used
with
a
properly
grounded and
polarized
power
supply
socket.
The
AC
Power
cord supplied
is
for
the
USA
(UL)
and
Canada
(CSA)
for
use
with
the display
unit.
For
use
in
other
countries,
make
sure the
AC
Power
cord
meets
the safety
standards
of
the country.
Place the
AC
Power
cord
where
it
will
not
be
subject
to stress.
Use
only
Panasonic
provided accessories or the exact
equivalent.
2)
Usage
The
monitor
power
switch
does
not
completely
turn
off
the
AC
Power
to
the monitor's
circuits
and
places the monitor
into
a stand-by
mode,
which
consumes
about
0.1
W.
This stand-by
mode
gives
no
operation
until
the
power
switch
is
turned
ON.
To
totally
remove
power,
the
AC
Power
cord
must be
disconnected
completely.
Pulling
on
the
AC
Power
cord
or
VGA
Signal
Cable can
damage
the display
unit
(monitor)
and can cause
the
unit to
fall
and
possibly
cause
personal
injury.
Receiving
trouble.
If
there
is
a
television set or
other display
unit
nearby,
keep
your
display
unit
as
far
away
from
it
as
possible.
Mutual
interference
can cause image
distortion
or noise.
Long exposure
to
rubber
or
vinyl
products
can
stains
the
cabinet.
Keep
the monitor
from
physical
shock
when
moving.
Be
careful
of
the
Cathode
Ray
Tube
(CRT).
Do
not
place anything
on
the monitor.
Also take
good
care
of
the
AC
Power
cord:
Do
not place
any
objects
on
the
AC
Power
cord.
Do
not
attempt
to
extend, shorten or
tie
it
into
a
knot.
3)
Product
Care
Prior to
cleaning your display
unit,
disconnect the
AC
Power
cord
and
the
VGA
Signal
Cable from
the display
unit.
Use
a
clean,
soft,
dry
cloth to
clean the outside
of
the
monitor
or the
CRT
surface.
If
the monitor or
CRT
surface
is
very
dirty,
wet a
clean,
soft cloth
with neutral
detergent
(such
as dishwashing
detergent)
and
water,
squeeze
it
tight
until
almost
dry,
wipe
the
monitor or
CRT
surface
with
it,
and
finish
by wiping
with
a
clean dry
cloth.
Do
not
use
any
solvents.
Do
not rub or
strike
the monitor
with
anything hard
or
harsh
as
this
may
scratch,
mar
or
damage
the monitor permanently.
Do
not
use a
chemical
duster or polish-cleaner
because
it
can
adversely
affect
the
unit
and
peel the
paint coat.
-2-
loading

Este manual también es adecuado para:

Tx-d7f21