Idiomas disponibles
Idiomas disponibles
Opening the safe with the admin code
•
Press the ENTER button.
•
Enter the 8-digit admin code (factory default code: 1-2-3-4-5-6-7-8).
and confirm with ENTER button.
The display shows „PASS 1" and counts down for 10 seconds.
After this time has elapsed, the door will open automatically.
Caution: When the admin code is entered, the last programmed user code is
shown on the display briefly and then deleted. The user code must now be
re-programmed (see „Programming the user code").
Programming the admin code
The safe door must be open with the bolts extended out of the door.
•
Press the ENTER button
•
Enter the admin code (factory default code: 1-2-3-4-5-6-7-8) and confirm
with ENTER button
The display shows „PASS 1" and counts down for 10 seconds. Within this
•
time, press the ENTER button again
•
Now enter the new admin code (8 digits) and confirm by pressing ENTER
•
„REPEAT" will appear on the display
•
Enter the new admin code a second time and confirm with ENTER.
•
The new admin code is saved when you see „GOOD" shown on the display
•
You will also hear 2 short beeps to confirm
A new admin code has been successfully programmed.
Chapter 2: Operation with fingerprint
Opening the safe with a fingerprint
•
Press the ENTER button.
•
For the fingerprint to be recognised it must be clean and dry.
•
Press your finger on the sensor with gentle pressure. The light ring will
illuminate with a blue light and 2 x short beeps can be heard.
The door will open automatically.
If 3 x short beeps are heard, the fingerprint was not recognised, please try
again.
Programming mode: learning and deleting fingerprints
The door must be open and the bolts must be retracted inside the door.
•
Press the ENTER button.
•
Enter the admin code and confirm with ENTER.
The following changes can now be made:
Pure-Safe Electronic E FP
Add a new fingerprint
•
Enter the digits „23" on the keypad and confirm with the ENTER button
„STEP1" appears on the display.
•
For a fingerprint to be programmed it must be clean and dry.
•
Place your finger on the sensor with gentle pressure until „STEP2" appears
on the display. The light ring will illuminate blue and 1 beep will be heard.
•
Take your finger off the sensor and place the same finger on the sensor
again with gentle pressure until the display shows „STEP3" and 1 beep can
be heard.
•
Take your finger off the sensor and place the same finger on the sensor
again a third time with gentle pressure until the display shows „GOOD" and
the ring light is illuminated with a green light and 1 beep is heard.
The fingerprint has been successfully programmed.
If you see the message „FP-ERROR" on the display and hear 3 short beeps, the
programming process has been aborted. The entire process must be repeated.
This happens, for example, if the finger on the sensor has been placed for too
long.
If you want to program additional fingerprints, start the whole process
(from programming mode) again.
Delete all stored fingerprints
•
Enter the digits „33" and confirm with ENTER button.
•
„GOOD" will appear on the display and 1 beep will be heard.
All fingerprints have been successfully deleted.
Error messages
FP-ERROR
Fingerprint not recognised (e.g. finger too dry,
too wet, injured, wrong finger)
CODE-ERROR
Incorrect code entry
BLOCK
The bolts hit an obstacle and cannot
extend to the end
LOW BATT
Batteries are low and should be replaced
ERROR 1
Electronic lock error.
Use the emergency key to access the safe.
Changing the batteries
A warning message „LOW BATT" is shown on the electronic lock display when
the batteries are nearly exhausted and need replacing. Please change as soon
as possible.
•
Open/unlock the safe.
•
The battery compartment is located on the inside
•
of the door.
•
Remove the screw on the battery compartment
cover with a Phillips screwdriver.
•
Remove and discard the batteries according to the
disposal instructions (see right).
•
Replace the 4 x AA Mignon LR 6 Alkaline with new
ones. Be sure to insert the batteries in the correct
direction as per the drawings. Please use high
quality batteries and not rechargeable ones.
•
Replace the battery compartment cover and
tighten the cover screw.
Warranty
BURG-WÄCHTER products comply with the technical standards in force at the
time of production and adhere to our own quality standards. The guarantee
only covers defects which can be proved to have resulted from production or
material defects at the time of purchase. The warranty ends after two years from
the date of purchase, further claims are excluded. Defects and damage caused
by e.g. transport, incorrect operation, improper use, wear etc. are excluded
from the warranty. The batteries are not included in the guarantee. A short
description of any defects identified must be made in writing and the device
returned to the place it was purchased, together with the purchase receipt.
After the device has been tested, and within a appropriate period of time, the
guarantor will decide whether or not to repair or exchange the item.
Note:
In order to deliver a flawless and high quality product to you and to better
assist you in case of service or repair, it is necessary that faulty or defective
devices along with the valid administrator code be presented to your dealer
together with the purchase receipt.
For returns, all undamaged device parts must furthermore be in the factory
setting due to your right of revocation. Failure to comply with this will invalidate
the warranty.
Disposal of the device
Please help us avoid unnecessary waste. Should you intend to dispose of
this device at any time, please remember that many components of this
device contain valuable materials that can be recycled.
Please be aware that electrical and electronic equipment and
batteries marked in this way must not be disposed of with
household waste but collected separately. Please obtain
information on the collecting points for electrical waste from the
responsible authority of your city/municipality.
BURG-WÄCHTER KG hereby declares that the present Device
complies with the directives 2014/30/EU, (EMC) and 2011/65/EU
(RoHS) compliant.
The full text of the EU declaration of conformity is available at the
Internet address www.burg.biz.
Safety recommendation
Please clean the keyboard operating surface periodically with a microfibre
cloth (e.g. glasses cleaning cloth for spectacles) to remove any fingerprints
on the keyboard surface.
Printing and typesetting errors as well as technical changes reserved.
English I 5
