Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
IQAmerica,
Wired+Wireless Designer Doorbell
Model PC-7110
Instructions • Please retain these instructions for future reference.
You have purchased a Universal Door
Chime
that serves all residential applications.
It can
be installed
as a Wired chime,
where
the power is supplied by a transformer with wires, or it can be a Wireless
chime powered by 3 C cell batteries. Use the following guidelines to assist you in deciding
the mode
that best serves your application:
If you are building a new house:
The Wired mode would be best if you are having an electrician
install
the door chime.
The electrician will install a transformer and run
the wires for
the door chime as well as pushbuttons.
You can also elect to use the Wireless mode. However, the batteries
in
the chime and
pushbuttons will need to be replaced periodically.
If you are replacing a working Wired Doorbell:
The Wired mode would
be the best option.
If you have a wired doorbell, but it doesn't work:
First install this
chime
in the Wired mode.
Connect the wires as explained in the section
"Replacing a Wired Doorbell".
If
the chime works, this is the best option.
If the chime does not work, purchase either 1 or 2 IQ America Wireless Pushbuttons and follow the
instructions for the
Wireless mode.
If your home does not have a wired doorbell, you should use the Wireless Mode.
This package contains:
Universal Chime and Decorative Cover
2 screws and 2 wall piugs for installing door chime
1 Diode
^|3|-
WIRED MODE: New Installations
New installations
will require
a 16V10W transformer. It is suggested that this be installed by
a licensed electrician.
You will require: (for Wired option)
A small Phillips head screwdriver.
(For
new installations)
Transformer 16V 10W(IQ America DT1610)
(For new installations) 2 Doorbell Pushbuttons
4 screws for installing doorbell pushbutton
1 Diode
Installing the Transformer
Warning; Turn power off at fuse or circuit breaker before installing transformer. Transformer should
be mounted
on or near a junction box. They can also be mounted
to the electricai service panels.
Junction boxes in utility rooms, crawl spaces, or basement are preferred. Avoid attic locations.
Failure
to use
a transformer
with
adequate power will result in loss of sound or
may result in the chime being faulty.
Contact a qualified electrician if you have any questions as to the suitability of the system
or any doubts
about your ability to wire
this correctly.
Remove Decorative Chime Cover
Remove the decorative cover by simply pulling it away from the rear casing.
When replacing
the cover,
simply
press it back on the base.
Install the Door Chime (Refer to Figure 1)
Position the
chime as shown
in Figure 1.
(The chime base can also be installed in the
horizontal position.) Route the wires as shown and install the chime using
the screws provided,
Figure 1
Figure 2
REAR PUSH
REAR
Install the Front Doorbell Pushbutton (Refer to Figure 2}
A small electrical component called a 'diode' is supplied with the chime. Install the diode across the
terminal screws of the Front Doorbell pushbutton as shown in Figure 2 & 3. Without this diode the
chime will not work Connect the wires to the Front Doorbell Pushbutton. Install the Front Doorbell
Pushbutton in the desire location using the screws provided.
Install the Back Doorbell Pushbutton (Refer to Figure 2}
Connect the wires to the Back Doorbell Pushbutton, Install the Back Doorbell Pushbutton in the desired
location using the screws provided (No diode required).
Wiring Instructions For New Installation (Refer to Figure 3)
1. Turn off trie power supply,
2. Connect one wire from the Front Doorbell Pushbutton to the FRONT terminal of the Chime Base.
3. Connect the other wire from the Front Doorbell Pushbutton to one Terminal of the Transformer.
4. Connect the TRANS
terminal of the Chime to
the other Terminal of the
Transformer.
5 If the Back Doorbell
Pushbutton is used,
connect one end of the
wire from the Back
Doorbell Pushbutton to
the REAR terminal of
the Chime,
6. Connect the other end of
the Back Doorbell Pushbutton
to the 1 st Terminal of the Transformer.
7. Turn on the powerto the doorbell.
8. Press the doorbell pushbutton. The chime should respond with a tune. If not, go to the
Troubleshooting section.
Replacing a Wired Doorbell
1. Turn off the power supply.
2. Remove the decorative cover by simply pulling it away from the rear casing. When replacing
the cover, simply press it back on the base.
3. use tape to marx me wires ana men disconnect the wires from doorbell.
4. Position the chime as shown in Figure 1. (The chime base can aiso be installed in the
horizontal position.) Route the wires as shown and install the chime using the screws provided.
5. Connect the wires to the Door Chime.
Transformer
Supply
Output
FRONT PUSH
Figure 3
Figure 4
6. A small electrical component called a 'diode' is supplied with the chime. Install the diode
across the terminal screws of the Front Doorbell pushbutton as shown in Figure 2 & 3,
Without this diode the chime will not work. Connect the wires to the Front Doorbell Pushbutton.
Install the Front Doorbell Pushbutton in the desire location using the screws provided.
7. Turn the power on.
WIRELESS MODE
You will require: (for Wireless option)
A small Phillips head screwdriver.
Doorbell Pushbuttons
3 C cell batteries
2 screws for installing doorbell pushbutton
1. Install the door chime using the hardware supplied.
2. Mount the IQ America Wireless Pushbutton following the
instructions provided and install the battery in the pushbutton.
3. Insert the C cell batteries in the order shown in Figure 4,
The Chime will play all of the tunes that are available when it is first powered up.
4. Program the wireless IQ America pushbuttons to the door chime
a. Press the front door pushbutton. The door chime will respond with a chime,
b. Program a second pushbutton at this time. Programming must be completed within
2 minutes of programming the first pushbutton. If more than 2 minutes has elapsed, go
to the To Reset the Chime Programming.
To Reset the Chime Programming, press and hold button A and B {Fig. 5) until the chime
sounds. The chime will play all of the tunes available indicating that previous programs have been
erased. Return to the Program the Doorbell Pushbutton Transmitter and repeat section.
Sound Selection: Refer to Figure 5 to select the sound
1. Press button A until the desired tone for the front doorbell is heard (See Tune Options Table),
Press the Front Doorbell Pushbutton to test the chime. (The chime tone can be changed at any
time by simply pressing this button to select another tone.)
2. If a Back Doorbell Pushbutton is used. Press button B until the desired tone is heard. Press
the Back Doorbell Pushbutton to test the chime.
3. Adjust the volume with the volume adjustment knob C.
Chime Options Table
1. Big Ben 2notes
6. Birthday Song
2. Big Ben Snotes
3. Traditional 1note
4. Traditional 2notes
5. Traditional Snotes
7. Merry Christmas
8. Auld Lang Synn
9. Beethoven
10. U.S. National Anthem
Replace the Decorative Chime Cover
as shown in Figure 6. Position the decorative
cover and press down until it snaps in place.
The cover can be installed in either direction.
Specification
Range
Up to 300 ft
Power supply
16V Transformer
Chime Not SoundJng;
Verify Diode is attached secure
Diode may be positioned at the
Chime Sounds Cniy V*ile Kee
ly to the Front Door bell Pushbutton,
wrong polarity. Reverse the diode.
ping Pushbutton Pressed
Reverse the direction of the diode on the front door pushbutton.
e Not Sounding:
Check that all batteries have been inserted correctly. The doorbell pushbutton LED
light should come on when the pushbutton is pressed,
Chime may be positioned out of range of the doorbell pushbutton.
Move your chime closer to the doorbell pushbutton.
Note: During the programming cycle, the transmission range may be
reduced and will resume optimum range after 2 minutes.
A metallic object may be blocking the signal from the doorbell pushbutton.
Experiment with the location of the chime to see if you can move it in to a more suitable place.
The battery in the doorbell pushbutton or chime may need replacing.
If the pushbutton LED light (B) flashes 5 times after being pushed, replace the battery.
Note: \ftAien replacing batteries the chime will retain its programming.
Note: In cold conditions, poor location or environment, operating at maximum range it IE
advisable to replace the battery more frequently before the indicator light flashes
(i.e. every 12-18 months) to maintain optimum performance.
The doorbell pushbutton and chime haven't been programmed.
Reset the automatic programming of your chime and doorbell pushbutton by Pressing and
holding down chime selection buttons A and B (Figure 5) for 5 seconds. The chime will soun
all of the tunes available indicating the programming has been erased. Program the doorbell
pushbutton following the installation instructions.
other problem, call 1-800-296-1869 Mon-Fri between 9 am and 5pm EST
IQ America Five Year Warranty
This is a "Limited Warranty" which gives you specific legal rights You may also
have other rights which vary from state to state and province to province
For a period of five years from the date of purchase, any malfunction caused by factory
defective parts or workmanship will be corrected at no charge to you. To obtain a refund or a replacement,
return the product to the place of purchase
NOT COVERED: Repair service, adjustment and calibration due to misuse abuse or
negligence Unauthorized service or modification of the product or of any furnished component will void this
warranty. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of
use or unauthorized service.
This warranty covers only IQ America products and is not extended to other equipment
and components that a customer uses in conjunction with our products.
This warranty is expressly in lieu of all other warranties, express or implied, including any
warranty, representation or condition of merchant ability of that the products are fit for any particular purpose
or use, and specifically in lieu of all special, indirect or incidental or consequential damages.
Repair or replacement shall be the sole remedy of the customer and there shall be no liability
ur, nit pan ur it* mnciiuo iur an; speQOi, mailed, incioemai or uuns,eijLjeiilidl UdmdUes, including Dill HOI
limited to any loss of business or profit, whether or not foreseeable. Some states or provinces do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. Retain receipt for warranty claims.
^
_^___
