Bell & Ross BR 03-94 BLACKTRACK Manual página 3

ENGLISH
BR 03-94 BLACKTRACK
LTD 500 PCS
BR-CAL.301
: mechanical with automatic winding. Calibre BR-CAL.301. Power reserve
Movement
approximately 40 hours. : hours, minutes and sub seconds. Chronograph:
Functions
30-minute and 60-second counters. Date with quickset. Time-setting with hacking
function. : 42 mm in diameter.
Case
GENERAL USAGE
When the watch has stopped (crown in position 0) : wind the
Starting the watch.
movement by rotating the crown clockwise. After approximately 40 rotations, the
watch is fully wound (the winding mechanism does not have a stop to prevent over-
winding). The power reserve is approximately 40 hours when fully wound. When the
watch is worn, the automatic mechanism will wind the movement.
Pull the crown out to position 2. The seconds hand will stop, enabling you to set the
time to the nearest second. Set the time by rotating the crown in the required direc-
. Quickset* (crown in position 1) : pull the crown out to position
tion.
Setting the date
1 and set the date by rotating the crown anticlockwise. S low setting (crown in position
2): to ensure the date changes at midnight rather than noon, it is recommended you
set the date by adjusting the hands of the watch. Pull the crown out to position 2 and
turn the hands until the date changes. Then set the precise time.
A
B
C
D
E
F
(x4)
G
STRAP MOUNTING
Attachments (G) with no visible screws
A spring bar is used to fit the strap to the case attach-
ments. This bar must be removed carefully using the
appropriate tool provided with the watch in the box.
IMPORTANT
*Quickset date setting. As with all mechanical watches with a date function, quickset
date setting (crown in position 1) MUST NOT UNDER ANY CIRCUMSTANCES be carried
out between the times of 9 P .M. (21:00) and 3 A.M. (03:00).
Magnetic fields. Magnetic fields can adversely affect the accuracy of your watch. Also,
we would recommend that you avoid placing your watch near electronic devices that
may generate large magnetic fields (radio, smartphone, television, computer, tablet,
loudspeakers etc.).
Once the watch is set, to ensure perfect water resistance, push the
Water resistance.
crown back to position 0. Never operate the crown underwater.
Note: The 4 slotted screws (F) mount the bezel to the case and ensure the water
resistance of the watch. To benefit from the Bell & Ross warranty, these screws must
never be unscrewed.
USING THE CHRONOGRAPH
The chronograph function can measure time in minutes and seconds.
Measuring the time.
1 press of Pusher P
st
2 press of Pusher P
nd
3 rd press of Pusher P
Measuring the time with an interruption
1 st press of Pusher P
2 press of Pusher P
nd
3 press of Pusher P
rd
.
Setting the time
This allows one or several time intervals to be subtracted from the total time
measured.
4 press of Pusher P
th
5 th press of Pusher P
A.
Minute hand
P
B.
Chronograph 60-second hand
C.
Hour hand
D.
Chronograph 30-minute counter
E.
Seconds hand
F.
Case attachment screw
0 2
G.
Strap attachment
H.
Date
I
I.
Crown
P .
P
1
Pusher 1. Start/Stop
2
P .
2
Pusher 2. Reset
0.
Wind the movement manually (rotate clockwise)
1.
Set the date (rotate anticlockwise)
H
2.
Set the time (rotate in either direction)
MAINTENANCE
After being immersed in seawater, it is recommended to carefully rinse off the watch
and strap with fresh water. It is also recommended to have the water resistance of
your watch checked every two years. To ensure a service that meets the brand's exact-
ing standards, any servicing of your watch must be carried out by the Bell & Ross
service centre or a watchmaker approved by Bell & Ross.
INTERNATIONAL WARRANTY
To benefit from your 2-year international warranty, your card must be activated at the
time of purchase by your approved Bell & Ross point of sale, and presented every time
an operation is performed. You can now access the digital version of this card and all
the information relating to your watch by scanning the QR code or visiting:
www.bellross.com/warranty
To ensure a service that meets the brand's exacting standards, any servicing of your
watch must be carried out by the Bell & Ross service centre or a watchmaker approved
by Bell & Ross. The warranty does not, however, include:
. Any damage caused by accidents or by inappropriate or improper use of the watch
(e.g. violent impacts, crushing, rough handling of the clasp).
. Any damage caused by repair or disassembly operations carried out by a retailer or
after-sales service centre not approved by Bell & Ross.
. The consequences of the watch and bracelet/strap ageing and normal wear and tear.
3
: sets off the time measurement.
1
: stops the time measurement.
1
: stops and resets the chronograph.
2
.
: sets off the time measurement.
1
: stops the time measurement.
1
: restarts the time measurement.
1
: stops the time measurement.
1
: stops and resets the chronograph.
2
(NEVER UNSCREW)