Palram Arcadia 5000 Instrucciones De Montaje página 5

IMPORTANT
Please read these instructions carefully before you start to assemble this product
.
Please
carry out the steps in the order set out
in
these instructions.
Keep these
instructions
in
a
safe place
for future
reference.
Safety advice
For
safety purposes we strongly recommend the product to be assembled by at least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves, eye
protection,
and long sleeves
when assembling or performing any maintenance
on
your product.
Do
not attempt to assemble the product
in
windy or wet conditions.
Do not
attempt to assemble the product if you
are tired, have taken drugs,
medications or alcohol, or if you are prone to dizzy spells.
Dispose of
all
plastic
bags safely
-
keep them away from children's
reach.
Keep
children
away
from the assembly
area.
When using
a
stepladder or power tools, make sure
that
you are
following
the manufacturer's
safety advice.
Do
not climb or stand on the roof.
Do
not hang or
lay
on the profiles.
Heavy articles should not
be
leaned against the poles.
Keep roof and gutters clear
of
snow,
dirt
& leaves.
Heavy snow load on the roof
can make
it unsafe to stand below or nearby.
If
color
was
scratched during assembly it
can be fixed.
Cleaning
instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do not
use
acetone, abrasive cleaners, or other special detergents to clean the panels.
Clean
the product once assembly
is
complete.
Before
starting assembly
Choose your
site
carefully before beginning assembly.
The
ground
surface must be
perfectly flat
and leveled and have
a
solid base such
as
concrete,
asphalt, deck etc.
Sort the parts and check against the content parts
list.
Parts
should
be laid
out
close at hand. Keep all small parts (screws etc.) in
a
bowl
so
they do
not get
lost.
Please
consult your local authorities if any permits are required prior to constructing the product.
Tools &
Equipment
T001
(Supplied)
During Assembly
UI
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and assistance.
Attention
During assembly
use
a
soft surface
below the parts to avoid scratches and
damages.
Please
make
sure
you install the panels with the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
and remove the sticker
as
panels are in place.
M
Steps
Step
1: In
the next steps we will be making preparations for assembling the product,
use
a soft
surface
below the parts to avoid scratches and damages.
Step 6:
Use
silicone sealant on both sides of part
#
8969.
Step 7: Note the
profiles'direction
by the holes on each edge,
see
drawings
a
& b.
Step 18: Note the direction of the bows
at
the products'
edges,
do not tighten the
screws in
drawing
b.
Step 19: Tighten the
screws
of
all bows.
Step 25: Make
sure all
panels
are
placed with the
"THIS SIDE
OUT" sticker facing up
.
Make
sure
the panels
are
inserted
all
the way into the profile
in
the middle.
Step 29: Make
sure
the edge profiles
are in
line with the longitudinal beams,
see
drawing
c.
Step 34: Check the product's diagonals and make sure
they
are identical. Please level the posts
and adapt screws and plugs to your specific foundation type.
Tighten all screws at
the end of assembly.
Do
not tighten
screws
and nuts (8192
& 466)
until completion of assembly
process.
These
2
icons
indicate if screws'tightening
is
required or not.
A
Note:
Anchoring this product to the ground
is
essential to
its
stability and rigidity.
It
is
required to complete this
stage in
order for your warranty to
be
valid.