EN
ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given top
priority in the design of your pivoting head light.
INTENDED USE
The light is intended for general illumination. The product
can also be used as a laser pointer.
With the magnetic function, the product can be attached to
horizontal surfaces.
Do not use the product for any other purpose. Use of the
product for operations different from intended could result in
a hazardous situation.
LIGHT SAFETY WARNINGS
The light source of this luminaire is not replaceable.
When the light source reaches its end of life the whole
luminaire shall be replaced.
Use only with recommended battery pack and charger.
Any attempt to use another battery pack will cause
damage to the product and could possibly explode,
cause a fire, or personal injury.
Do not disassemble the product.
If wrapped or in contact with fabrics, the lens can
produce sufficient heat to melt some fabrics. To avoid
serious personal injury, never allow the lens to come in
contact with anything.
Do not place the product or battery pack near fire or
heat. This will reduce the risk of explosion and possible
injury.
Remove the battery pack or disconnect the mains power
before starting any work on the product.
Do not store the product in a damp or wet location, or in
a location where the temperature may reach or exceed
40°C. For example, inside sheds, vehicles, or metal
buildings in the summer.
Do not direct the light beam at persons or animals and
do not stare into the light beam yourself (not even from
a distance). Staring into the light beam may result in
serious injury or vision loss.
Use the magnets to mount the product on 22-gauge low
carbon steel surface. Minimum thickness: 0.6 mm.
LASER SAFETY WARNINGS
Laser radiation. Do not stare into beam. Class 2 laser
product.
Risk of severe eye injury if the laser beam is directed at
persons or animals. Avoid direct eye exposure.
Do not direct the laser beam towards other people.
Do not operate the product around children or allow
children to operate the laser.
Avoid using the product on reflective surfaces. The laser
beam may be reflected at the operator or other persons.
Store the product indoors and avoid substantial knocks,
continuous vibration or extreme temperatures.
Always keep the product away from dust, liquids and
high humidity. They may damage internal components
or affect accuracy.
Do not remove or deface warning labels on the product.
Do not disassemble the product.
Avoid heavy impact to or dropping of the laser. The
accuracy of the laser should be checked before use if
it has been dropped or subjected to other mechanical
stresses.
Do not operate the product in explosive areas or in
extreme environments.
BATTERY SAFETY WARNINGS
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack, or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 43.
1. LED lens
2. Laser exit window
3. Adjustable head
4. On/Off switch
5. Magnetic battery cap
6. Belt clip
7. Battery
8. USB charging cable
9. Operator's manual
10. USB power adaptor
MAINTENANCE
Use only original accessories and spare parts. Should
components that have not been described need to be
replaced, please contact an authorised service centre.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3
