Items Supplied - FLORABEST KH 4236 Instrucciones De Uso Y De Montaje

Items supplied

1 1 x Barbecue skewer
(incl. 2 x Barbecue racks and 1 x Wooden handle)
2 1 x Wind protector, left
3 1 x Wind protector, Middle
4 1 x Wind protector, right
5 1 x Grill
6 1 x Firebowl
7 1 x Handle
8 2 x Handle holder, short
9 2 x Stand braces
0 2 x Cross braces
q 5 x Storage slats, long
w 2 x Wheels
e 1 x Axle
r 2 x Wheel brace
t 2 x Storage holder, long
z 2 x Reinforcing braces
u 3 x Storage slats, short
Connection elements
M5x10 M5x12 Ø4x10
25x 22x 2x
Assembly
Attention!
To avoid possible injury, the screw heads should
always face outwards. First tighten all screw
connections down when the assembly is complete,
this will help avoid undesirable material tensions.
1. Place the fi rebowl 6 with the fi ve holes the
longer sidewall to the rear, on the work surface.
2. Connect a long storage holder t with the wheel
braces r by means of the washers Ø 5.4,
M5 x 10 screws and nuts M5.
Please take note that only the lower holes are to
be used for the screws.
M5 M8 Ø5.4 M4x10
47x 2x 47x 2x
3. Assemble the wheel braces r with the assem-
bled long storage holder t to the left on the
fi re bowl 6 by means of the washers Ø 5.4,
2 M5 x 12 screws, 2 M5 x 10 screws and
nuts M5. For this, use the upper hole in the
wheel braces r.
4. Secure the reinforcing braces z with the
wheel braces r by means of the washers Ø
5.4, M5 x 10 screws and nuts M5. Connect
the reinforcing braces z with the long storage
holder t by means of the washers Ø 5.4,
M5 x 10 screws and nuts M5.
5. Assemble the short handle holder 8 and stand
braces 9 as described in points 2. and 3.
Fix the handle 7 between the short handle
holders 8 and then secure them by means
of the wood screws Ø 4 x 10.
6. Place the cross braces 0, with the 5 holes
facing upwards, between the wheel braces r
and the stand braces 9. Screw these together
by means of the washers Ø 5.4, M5 x 10
screws and nuts M5.
7. Fix the fi ve long storage slats q to the cross
brace 0. Secure them using washers Ø 5.4,
M5 x 12 screws and M5 nuts.
8. Assemble the short storage slats u for the
storage holder t by means of the washers
Ø 5.4, M5 x 12 screws and M5 nuts.
9. Guide the axle e through the lower boreholes
on the wheel braces r and secure the placed-
on wheels w with the self-securing nuts M8.
10. Join the wind protector elements 2 3 4
together with 2 M5 x 10 screws and M5 nuts
(only at the top). When done, secure the wind
protector element 2 3 4 from inside onto
the fi rebowl 6 by means of the washers
Ø 5.4, 2 M5 x 12 screws, 3 M5 x 10 screw
and nuts M5.
11. Secure the wooden grip 1 onto the rear part
of the skewer 1, (straight edge) with light
hammer blows. Slide the barbecue racks 1
onto the skewer. Secure the barbecue racks
1 with the eye screws M4 x 10.
12. Place the grill 5 and the skewer 1 inside the
wind protector 2 3 4.
- 15 -