Idiomas disponibles
Idiomas disponibles
TRACTOR
Always
observe
safety rules when per-.
forming
any maintenance.
BRAKE
OPERATION
If tractor
requires
more than five (5) feet to
stop at highest
speed in highest gear on a
level, dry concrete
or paved surface,
then
brake must be service&
(See "TO CHECK
BRAKE"
in the Service
and Adjustments
section
of this manual).
TIRES
• Maintain
proper air pressure
in all tires
(See PS1 on tires)_
• Keep tires free of gasoline,
oil, or insect
control chemicals
which can harm rubber.
• Avoid stumps,
stones,
deep ruts, sharp
objects
and other hazards
that may
cause tire damage°
NOTE:
To seal tire punctures
and prevent
flat tires due to slow leaks, tire sealant
may be purchased
from your local parts
dealer. Tire sealant
also prevents
tire dry
rot and corrosion,
OPERATOR
PRESENCE
SYSTEM
AND
REVERSE
OPERATION
SYSTEM
(ROS)
Be sure operator
presence
and reverse
operation
systems
are working
properly
If
your tractor
does not function
as de-
scribed,
repair the problem
immediately,
• The engine should
not start unless the
brake pedal is fully depressed,
and the
attachment
clutch control
is in the disen-
gaged position.
CHECK
OPERATOR
PRESENCE
SYSTEM
• When
the engine is running,
any at-
tempt by the operator
to leave the seat
without
first setting
the parking
brake
should
shut off the engine,
• When
the engine is running
and the
attachment
clutch is engaged,
any at-
tempt by the operator
to leave the seat
should
shut off the engine,
• The attachment
clutch should
never op-
erate unless the operator
is in the seat.
ROS "ON" Position
Engine "ON" Position
(Normal Operating)
CHECK
REVERSE
OPERATION
(ROS)
SYSTEM
• When the engine
is running with the
ignkion
switch in the engine
"ON" posi-
tion and the attachment
clutch engaged,
any attempt
by the operator
to drive in
reverse
should
shut off the engine.
• When the engine
is running with the
ignition
switch in the ROS "ON" position
and the attachment
clutch engaged,
any attempt
by the operator
to drive in
reverse
should
NOT shut off the engine-
BLADE
CARE
For best results
mower blades must be
sharp°
Replace worn, bent or damaged
blades,.
A CAUTION:
Use only a replacement
blade approved
by the manufacturer
of
your tractor,
Using a blade not approved
by the manufacturer
of your tractor
is
hazardous,
could damage
your tractor
and
void your warranty.
BLADE
REMOVAL
1o Raise mower to highest position
to al-
low access to blades.
NOTE:
Protect
your hands with gloves
and/or wrap blade with heavy cloth.
2.
Remove
blade bolt by turning
counter-
clockwise.
3.
Install new blade with stamped
"GRASS
S1DE" facing the ground.
IMPORTANT:
To ensure
proper assembly,
center hole in blade must align with star
on mandrel
assembly.
4o Install and tighten
blade bolt securely
(45-55 Fto Lbs. torque).
IMPORTANT:
Special
blade bolt is heat
treated,
Mandrel
Assembly
t_'\
" Star
Center Hole
BATTERY
Your tractor
has a battery charging
system
which is sufficient
for normal use.
How-
ever, periodic
charging
of the battery with
an automotive
charger
will extend its life,
Keep battery and terminals
clean,
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge
at 6-10 amperes
for 1 hour.
NOTE:
The original
equipment
battery
on
your tractor
is maintenance
free. Do not
attempt
to open or remove caps or covers.
Adding
or checking
level of electrolyte
is
not necessary.
18
