Idiomas disponibles
Idiomas disponibles
In order to replace the cartridge you must place it from below
against the head'shell so that the front edges are flush. Please
ensure that the cartridge lies absolutely flat on the head shell
before pulling the tonearm lift to the front in order to lock it
in position
(Fig.
12).
You
may then, if desired, reinsert the
safety screw (Fig. 11/(11))
Stylus
The stylus is subject to natural wear and tear during normal
playing. Therefore, we recommend you occasionally check the
stylus and, in the case of diamond styli, this should be carried
out after approximately
300 playing hours,
Your specialist
dealer will be pleased to do this for you free of charge. Worn
or damaged (splintered) styli chisel the modulation from the
grooves and destroy records. Therefore, only use as replacement
the stylus
types
recommended
in
the technical
data
of the
cartridge.
Imitated styli result in audible quality losses and in
creased wear and tear of records. Please remember that, for
physical reasons, the stylus holder with the diamond stylus is
extremely
fine and must therefore be necessarily sensitive to
impacts, shocks or uncontrolled movement.
When removing the stylus please note the information contained
on the separately enclosed data sheet referring to the cartridge
on your unit
Installing 1/2-inch cartridge
Your
Dual
turntable
will provide excellent tracking and re-
production if used in conjunction with ULM
(Ultra low mass)
cartridges.
However
the tonearm
characteristics are so good
that even substantially heavier
1/2' cartridges will operate
optimally.
If you wish to fit a standard 1/2" cartridge, please
proceed as follows:
1) If necessary, remove the safety screw (Fig. 11/(11))
2) Remove
the cartridge from the head shell as described in
the section "Replacing the cartridge"".
Attach the 1/2" cartridge to the mounting plate with the
aid of the system installation gauge and, using the acces-
sories enclosed with the cartridge. This has been correctly
installed if the tip of the stylus — viewed from above — is
in the V-shaped
recess
of the system
installation
gauge.
Viewed from the side, the stylus must be in the area of the
rectangular recess (Fig. 9)
4) Connect the connections of the head shell to the connecting
pins on the cartridge, The connections are color-coded
Red
R
right channel
Green
RG right channel ground
Blue
GL left channel ground
White
L
left channel
5) When
fitting the mounting plate together with the fitted
cartridge, please note the instructions contained in section
titled 'Replacing the cartridge"
6) Depending on the total weight of the cartridge system, screw
one or two of the disc-shaped additional weights (included
with the accessories) onto the tonearm counterweight (1)
3
Avant de mettre votre platine en marche pour la premiere fois,
lisez attentivement
cette notice d'emploi.
Cela vous évitera de
commettre
des erreurs de branchement
ou de commande et
d'endommager votre appareil.
Les éléments de commande
(1)
Contrepoids du bras avec antirésonateur de tuning
(2) Vis de blocage du contrepoids du bras de pick-up
(3) Supports du couvercle
(4) Réglage de la force d'appui du bras
(5) Réglage de la vitesse de descente du bras de pick-up
(6) Vis d'ajustage de la hauteur du bras
(7) Réglage d'antiskating
(8) Vis d'ajustage du point de pose du bras
(9) Support du bras avec surface d'appui
(10)
Réglage de la vitesse du plateau
(11)
Vis de fixation de la cellule
(12)
Poignée du bras / Verrouillage de la tête de lecture
(13)
Touche pour lever le bras 4 et descendre le bras w
12
Cartridge : Total weight « Including hardware
upto
6g
1 thin disc
upto
7g
1 thick disc
upto 9g
1 thick disc and 1 thin disc
up to 10g
2 thick discs
Screw the smaller thread of the special screw into the coun-
terweight (1). With the bevelled side to the outside, screw
the corresponding additional weights onto the thicker part
of the screw.
Now once again carefully balance the tonearm as described
in the section "Balancing the tonearm" and set the stylus
pressure and anti-skating force required for your cartridge.
After having mounted a 1/2 inch cartridge check the height of
the playing needle above the record with the pick-up arm lift
in position a also check that the needle lowers into the run-in
groove of the record. See parts "Cue control (Pause)" (page 11)
and 'Adjustment of tonearm indexing" (page 11)
Servicing
All the lubrication points have sufficient oil, Thus, your unit
will operate impeccably for many years under normal condi-
tions, Never try to lubricate any of the lubrication points your.
self.
If your record okayer should ever need servicing, either
take it to your specialist dealer or ask him
for the address of
the nearest authorized Dual Servicing Workshop.
Please make
sure that only original Dual replacement parts are used,
Should the unit ever be dispatched, make sure that this is
packed perfectly, if possible, by using the original packaging.
The platter
The balanced full-size aluminum alloy platter lies directly on
the motor spindle and, when placed in position, is automatically
fixed through its own weight. Additional locking is not neces-
sary and is also not provided for
Important! Remove the platter before transporting the unit!
Subsequent transport
If you wish to transport the unit long distances, we recommend
that the cover and the platter be removed. The counterweight
should
also
be removed.
Screw
the three transport
safety
screws back in position.
Ensure that the tonearm is locked and the stylus cover is in position.
Note: After each transport, the unit should be started once with
the tonearm
locked for the purpose of automatic adjustment
of the automatic shut off
First of all the POWER
button (21) and the START button
(15) must be depressed to initiate the start function (refer to
the section on "operation'')
Electrical safety
The unit complies with the International Safety Regulations
for radio and related devices (IEC 65)
7
(18)
Touche pour l'enclenchement de l'accord de hauteur du son
(19)
Syntonisation sonore
(20)
Stroboscope lumineux
(21)
Interrupteur secteur
Préparation
Déballage et mise en place
Retirez l'appareil et ses accessoires de l'emballage. Enlevez les
3 vis assurant la sécurité pendant le transport et qui portent
une rondelle rouge (Fig.
1). Conservez l'emballage d'origine et
ces 3 vis pour un éventuel
transport ultérieur
Posez le plateau avec précaution sur l'axe du moteur.
Glissez la pointe du contrepoids dans l'extrémité arrière du bras
de lecture én faisant bien attention à ce que la rainure en V de
l'axe soit bien dirigée vers le bas (Fig. 2)
