Idiomas disponibles
Idiomas disponibles
unscrew the cap by turning it counter-clockwise.
3. Add bar and chain oil until tank is full.
%ZSMH HMVX SV HIFVMW IRXIVMRK SMP XERO VI X SMP PPIV
cap and tighten by turning clockwise until hand
tight.
IMPORTANT: To allow venting of the oil tank,
small breather channels are provided
FIX[IIR XLI SMP PPIV GET ERH XLI WXVEMRIV XS
prevent leakage, and ensure machine is left in a
horizontal position when not in use.
It is important to use bar and chain lubricant (not
provided) that is formulated to perform over a
wide temperature range with no dilution required.
This can be found at the location where you
purchased this saw or your local hardware store.
Do not use dirty, used or otherwise contaminated
oils. Damage may occur to the bar or chain.Use of
non approved oil will void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store
E[E] JVSQ LIEX SV STIR EQI
Checking the Automatic Oiler
WARNING:Cutting edges on chain are sharp.
Use protective gloves.
Lift the Retractable Guard to the maximum position
JSV PYFVMGEXMSR EJXIV PPMRK YT XLI SMP XERO 7II
Fig.G2) Proper functioning of the automatic oiler
can be checked by running the Pruning Saw and
pointing the tip of the guide chain bar towards a
piece of cardboard or paper on the ground. If an
increasing oil pattern develops on the cardboard,
XLI EYXSQEXMG SMPIV MW STIVEXMRK RI -J XLIVI MW
no oil pattern, despite a full oil reservoir, contact
WorxNitro customer service agent or WorxNitro
approved service agent.
Caution: Do not touch the ground with the
chain. Ensure safety clearance of 40cm.
6. OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or
EPPS[ QIXEPPMG SFNIGXW MRXS ]SYV GLEVKIV SV FEXXIV]
pack connections because of an electrical failure and
hazard will occur.
NOTE: Your battery pack is UNCHARGED and you
must charge once before use.
The battery charger supplied is matched to the
Li-ion battery installed in the machine. Do not use
another battery charger.
(1) CHARGING YOUR BATTERY PACK (See Fig. H1,
H2)
Cordless Pruning Saw
The Li-ion battery is protected against deep
discharging. When the battery is empty, the
machine is switched off by means of a protective
circuit.
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool down
before recharging.
(2) TO REMOVE OR INSTALL BATTERY PACK (See
Fig. I)
Depress the Battery Pack Release Button to remove
the Battery Pack from your tool. After recharging,
insert the Battery Pack into the battery port. A
WMQTPI TYWL ERH WPMKLX TVIWWYVI [MPP FI WY GMIRX
until a click is heard. Check to see if the battery is
fully secured.
NOTE: When removing the battery pack, hold it
VQP] XS EZSMH HVSTTMRK ERH MRNYV]
(3) HOLDING AND CONTROLLING THE PRUNING
SAW (See Fig. J)
Hold and control the pruning saw with one hand on
the Grip Area – wrap your thumb around the Grip
Area.
2. SWITCHING ON AND OFF (See Fig. K)
ATTENTION: Check the battery pack before
using your cordless tool. Only use the battery
pack listed in the accessories section.
For switching on the tool, press the Lock-Out
&YXXSR XLIR JYPP] TVIWW XLI 3R3JJ 8VMKKIV ERH LSPH
in this position. The Lock-Out Button can now be
released.
For switching off VIPIEWI XLI 3R3JJ 8VMKKIV
3. CUTTING
IMPORTANT: Check recent replaced chain
tension about every 10 minutes during
operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying
on the ground. This will keep the chain from
touching the ground as it cuts through the log.
Touching the ground while the Chain is moving
is dangerous and will dull the Chain.
(3) When ready to make a cut, push the Lock-Out
Button completely in with the right thumb
and squeeze the trigger. This will turn saw on.
Releasing the trigger will turn the saw off. Make
sure the saw is running at full speed before
starting a cut.
(4) When starting a cut, slowly place moving chain
against the wood. The wood should be as close
XS XLI WE[ FSH] EW TSWWMFPI ,SPH WE[ VQP]
in place to avoid possible bouncing or skating
(sideways movement) of saw.
(5) Guide the saw using light pressure and do not
19
EN
