Idiomas disponibles
Idiomas disponibles
BEFORE STARTING
SAW
_,WARNING:
Be sure to read the
electrical
safety information
in the
SAFETY RULES section of this manual
before you begin, If you do not under-
stand the electrical
safety information
do not attempt to use your unit. Seek
help from someone
that does under-
stand the information
or call the cus-
tomer assistance
help line at
1-800-235-5878.
GUIDE BAR AND CHAIN OIL
The bar and chain require lubrication,
The manually-operated
chain oiler
provides
lubrication
to the chain and
guide bar. Be sure to fill the bar oil tank
before each cutting session. The oiler
activator/bar
oil cap must be used reg-
ularly and often enough to maintain
a
thin film of oil on the bar and chain
while saw is cutting.
It is recom-
mended
that the oiler actuator/bar
oil
cap be operated
every ten (10) sec-
onds and held for approximately
three
(3) seconds each time it is 3ressed.
OPERATING TIPS
For maximum guide bar and chain life,
we recommend you use Craftsman
chain saw bar oil. If Craftsman bar oil is
not available, you may use a good
grade SAE 30 oil until you are able to
obtain Craftsman brand. The oil output is
manually metered during operation.
Use
a funnel to fill the tank. Replace oil cap
securely. Check oil level after every 15
minutes of operation.
STOPPING
YOUR SAW
• Release the trigger switch.
• If motor does not stop, disconnect
the extension
cord. Discontinue
use
of the unit until repaired by a Sears
Service Center.
STARTING
YOUR SAW
1. Connect the saw to a power
source using the proper size exten-
sion cord (see SELECT AN EXTEN-
SION CORD).
2. Push in switch lock out button.
3.
Squeeze
and hold the trigger
switch.
• Check chain tension
before first use
and after 1 minute of operation.
See
CHECK CHAIN TENSION in the SER-
VICE AND ADJUSTMENTS section.
• Cut wood only. Do not cut metal,
plastics,
masonry, non-wood
building
materials,
etc.
• Stop the saw if the chain strikes a
foreign object. Inspect the saw and
repair parts as necessary.
• Keep the chain out of dirt and sand.
Even a small amount of dirt will
quickly dull a chain and increase the
possibility
of kickback.
• Practice cutting a few small logs using
the following steps. This will help you
get the "feel" of using your saw before
you begin a major sawing operation.
• Squeeze
the trigger switch and al-
low unit to reach full speed before
cutting.
• Begin
cutting
with the saw frame
against the log.
• Keep the motor at full speed the en-
tire time you are cutting.
• Release trigger switch as soon as cut
is completed, allowing motor to stop.
• Keep the cord away from the cutting
area.
Position cord so it will not be
caught
on branches
and the like
during cutting.
• To avoid losing control when cut is
complete,
do not put pressure
on
saw at end of cut.
• Stop motor before setting saw down.
TREE FELLING
TECHNIQUES
Check for broken or dead branches
which can fall while cutting causing seri-
ous injury. Do not cut near buildings or
electrical wires if you do not know the
direction of tree fall, nor cut at night
since you will not be able to see well,
nor during bad weather such as rain,
snow, strong winds, etc. If the tree
makes contact with any utility line, the
utility complany should be notified im-
mediately.
• Carefully plan your sawing operation in
advance.
• Clear the work area. You need a clear
area all around the tree so you can
have secure footing.
• The chain saw operator should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill
after it is felled.
• Study the natural conditions that can
cause the tree to fall in a particular
direction, such as:
• The wind direction and speed.
• The lean of the tree. The lean of a tree
might not be apparent due to uneven
