Appearance description:
13: Weather station low battery indicator
01: Light/snooze touch button
14: Indoor temperature and humidity
02: Mode button
15: Remote sensor low battery indicator
03: MEM button
16: Outdoor temperature and humidity
04: + button
17: Weather pattern
05: - / Wave button
18: Barometric pressure trend display
06: Alarm ON/OFF switch
19: Ice alert icon
07: Adapter input socket
20: Time DST icon
08: USB socket
21: Radio Controlled Icon
09: CH button
22: Battery compartment cover
10: Loop button
23: Stand cover
11: Rainbow button
24: Wall mounting hole
12: Time
TX: T1: Transmit indicating lamp T2: Wall mounting hole T3: Channel switch
T4: Battery compartment cover T5: Reset button
Initial operation: Open the Weather Station battery compartment cover
• Insert 2 x AA batteries observing polarity [ +/- marks]
• When you insert the batteries, all the icon on the LCD will light up for 3 seconds,
and you will hear a beep tone, then detect indoor temperature & humidity.
• The Weather Station will now start to make a connection to the outdoor remote sensor.
This operation takes about 3 minutes and will displayed by a flashing reception
RF antenna symbol in the OUTDOOR display area on the receiver.
• This now, Open the remote Sensor battery compartment cover,
Insert 2 x AA batteries observing polarity [ "+" and "–" marks]
• After receiver has created a connection to the outdoor remote sensor,
After 3 minutes it will enter the Radio control time receive mode.
Reception of the Radio signal:
• The clock will automatically search the DCF signal after 3 minutes of any restart
or changing of new fresh batteries. The radio mast icon starts to flash.
• At 1:00 /2:00 / 3:00 AM, the clock automatically carries out the synchronization
procedure with the DCF signal to correct any deviations to the exact time. If this
synchronization attempt is unsuccessful (the radio mast icon disappears from the display),
the system will automatically attempt another synchronization at the next full one hour.
This procedure is repeated automatically up to total 5 times.
• To start manual DCF signal reception, press and hold the "Wave" button for two
seconds. If no signals received within 7 minutes, then the DCF signal search stops
(the radio mast icon disappears) and start again at the next full one hour.
• During RC reception, to stop searching radio signal, press the "Wave" button once.
-02 -
F.Y.I.: A flashing radio mast icon indicates that the DCF signal reception has started
• A continuously displayed radio mast icon indicates that the DCF signal was received
successfully
• We recommend a minimum distance of 2.5 meters (8.2Feet) to all sources
of interference, such as televisions or computer monitors or switching power adapter.
• When receiving the DCF radio wave, it will automatically turn off the USB charging
and FM radio function.
• Radio reception is weaker in rooms with concrete walls (e.g.: in cellars) and in offices.
In such extreme circumstances, place the system close to the window.
• During the RC receive mode, only the "Light/snooze" and "Wave" buttons have
a function, other buttons are not functional, If you want to carry out other functions
of operation, please press "Wave" button to exit the RC receiving mode.
Manual time setting:
• Press and hold the "mode" button for 2 seconds, the temperature unit starts to flash.
Now use "+" and "-" buttons to set the temperature unit in °C or °F you need.
• Press "mode" button to confirm your setting, the 12/24HR start to flash.
Now use "+" and "-" buttons to set the 12/24 hour mode you need.
• Press "mode" to confirm your setting, the Time zones start to flash,
Now use "+" and "-" buttons set a correct time zone (-12 to +12).
• Press "mode" to confirm your setting, the Hour display starts to flash.
Now use "+" and "-" buttons to set the correct hour.
• Press "mode" to confirm your setting, the Minute display starts to flash.
Now use "+" and "-" buttons to set the correct minute.
• Press "mode" button to confirm your setting, the weather forecast pattern display
starts to flash. Now use "+" and "-" buttons to select the current weather pattern.
• Press "mode" to confirm your setting and to end the setting procedures,
Then it will return to the normal mode.
F.Y.I.: If there is no valid operation within 20 seconds, it will automatically return
to normal time mode from the set mode.
Setting the daily alarms:
• Push the "AL" switch to the on position, the LCD display the Alarm icon, at the same time
issued BI-BI sound (Except for RC), the alarm function is ON. Push the "AL" switch to the
off position, the ALARM icon will disappears from the display, the alarm function is OFF.
• Press once "mode" button, LCD display alarm time, then Press and hold "mode" button
for 2 seconds until hour of the Alarm time starts to flash. Use the "+" and "-" buttons to
set the required hour.
• Press "mode" button to confirm your setting, The Minute of the Alarm time starts to flash.
Use the "+" and "-" buttons to set the required minute.
• Press "mode" button to confirm your setting, the snooze time of the Alarm starts to flash.
-03-
