Commercial Electric 538661010 Manual De Uso Y Cuidado

UsE ANd CARE GUIdE
LEd sqUARE CANLEss sLIM dOWNLIGhT WITh NIGhTLIGhT
PAckAgE cONTENTS
Part Description Quantity
A LED Downlight 1
B Electrical Box 1
c hole Template 1
A
D Black Trim 1
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: rIsK of ELEcTrIc shocK. Ensure the electricity to the wires you are working on is shut off. Either
remove the fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
INSTALLATION
Item # 1000000000/Model # 538661010 can be installed into holes cut in the drywall that are between 4" and 4 1/3",
4" is suggested.
Item # 1000000000/Model # 538671010 can be installed into holes cut in the drywall that are between 6" and 6 1/3",
6 1/4" is suggested.
1. Make sure the power is turned off at the source to the location where the LED downlight (A) will be installed.
If InsTALLIng ThE LED DownLIghT (A) In A PrEExIsTIng hoLE:
a. remove the existing can or fixture and set aside since it will not be needed.
b. Measure the ceiling hole to make sure it is the correct size for the fixture.
If InsTALLIng ThE LED DownLIghT (A) In A nEw cEILIng LocATIon:
a. Place the hole template (c) over the desired location and trace the outline with a pencil.
b. cut out the marked opening in the ceiling with a hole saw (not included).
NOTE: 1/2" or 5/8" drywall recommended for easy installation.
2. Loosen the quick connects in clockwise directions and
detach the quick connects in the fixture body and J-box
3. Pick up the cover of the driver box as shown below.
remove one of the knock out holes on the side of the
electrical box (B), based on the installation position.
feed the power cord (not included) and all the electrical
connection wires through the open knockout hole in the
electrical box and tighten the power cord securely.
STEP 3.
B
Item # 1000000000/ 1000000000
Model # 538661010/ 538671010
4 IN., 6 IN.
c
B
D
STEP 1.
STEP 2.
Quick connects
Knock out hole
4. feed the wires from the electrical source through the open knock
out hole in the electrical box (B). Insert the hot, neutral wires from
the electrical source into the wire connectors of the black and
white wires in the electrical box (B). Insert the ground wire from
the electrical source into the wire connectors of the green wire in the
electrical box (B). close the electrical box cover.
5. Place the electrical box (B) through the cut-out hole in the ceiling
and position it where desired.
NOTE: The electrical box (B) must be no more than 16 inches from the edgelit downlight based on the length
φ 4 in.
of the connector cables.
Item # 1000000000
Model # 538661010
φ 6.25 in.
Item # 1000000000
Model # 538671010
6. Align the male connector from the electrical box (B) into the female connector from the LED downlight (A).
Twist the quick connects in counterclockwise direction and lock the quick connects in the fixture body and junction box.
7. one at a time, flip the spring clips on the LED downlight (A) up and insert into the opening in the ceiling. once both spring
clips are inside the cut-out, gently push the LED downlight (A) upward until the trim is flush with the ceiling surface.
NOTE: select the preferred color temperature of the light before inserting the LED downlight (A) into the ceiling opening.
STEP 6.
connector
A
8. restore power at the electrical panel.
Turn on the light switch to activate the fixture.
9. This downlight allows you to customize the color of the trim: white trim and Black trim (D). hold both sides of the
lamp, and remove the white trim as shown below.
NOTE: The product is shipped with the white trim installed on the downlight.
A
Power cord
(not included)
white trim
STEP 5.
B
STEP 7.
B
Quick
connects
STEP 8.
Take down
Black trim (D)
GND
STEP 4.
L
N
B
spring clip
A
Install