Idiomas disponibles
Idiomas disponibles
Tool Specifications
Jig Saws
Order Number
Power
Frequency
Amperage
127V
220 V
230 – 240 V
Stroke rate at no load
Stroke
Cutting
wood up to
Performance aluminum up to
in non-alloyed steel up to [mm]
Bevel cuts (left/right)
Base
Weight without cable, approx.
Protection class
*
The initial speed can present variations of +/- 400 min
Machine Elements
A
On/Off switch
B
Locking button for on/off switch
C
Wheel for adjusting sawing speed (4170)
D
Wrench
E
Screw
F
Saw blade*
G
Cutting angle Scale
H
Base plate
I
Screw
J
Vacuum cleaner adaptor*
* The accessories illustrated or described are not
included as standard delivery.
Introduction
This tool is intended for making cut-throughs and cut-outs in
wood, plastic, metal, ceramic plates and rubber, and is
suitable for straight and curved cuts with mitre angles to 45°
This machine is restricted to the domestic use, no being
indicated for professional works.
Read and save this instruction manual
Noise/vibration information
Measured values determined according to EN 50 144.
Typically the A-weighted noise levels of the tool are: Sound
pressure level: 84 dB (A).
Sound power level: 95 dB (A).
Wear ear protection!
The typical weighted acceleration is 12,4 m/s
General power tool safety instructions
.
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
SAVE THESE INSTRUCTIONS
1. Work area safety
a) Keep work area clean and well lit. Cluttered and poorly
lit areas can result in accidents.
4003
F 012 400 3..
[W]
380
[Hz]
50 / 60
[A]
3,1
[A]
–
[A]
1,7
-1
[min
]
3.000
[mm]
22
[mm]
55
[mm]
10
4
[°]
0 - 45
[mm]
184 x 93
[Kg]
1,6
E
/ II
-1
.
b) Do not operate power tools in the presence of
flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not misuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f) If it is not possible to avoid the use of the power tool
in humid or wet areas, use a residual current device
(RCD)protected supply. Use of an RCD reduces the risk
of electric shock.
g) In case of change need or substitution of the electric
2
cable, it should be made by an authorized and
qualified technical service. A damaged cable increases
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while if you are tired or under the
influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
12
4170
F 012 417 0..
400
50 / 60
3,6
1,8
1,8
*
800
... 3.100
22
65
10
4
0 - 45
184 x 93
1,7
E
/ II
