Oster 97 Manual De Instrucciones página 4

ABOUT THE CLIPPER
DO NOT USE THIS APPLIANCE UNTIL YOU HAVE READ THESE OPERATING INSTRUCTIONS
OPERATE ON VOLTAGE SPECIFIED ON APPLIANCE
HOW TO CHARGE THE UNIT
Place clipper on charging stand or connect directly to the power supply cord. This clipper has one control LED
INDICATOR.
Clipper In Charger
Charging Pulsing Green
Fully Charged Solid Green
Clipper Off Charger
Battery Level <20% Solid Red
Battery Level <10% Pulsing Red
Faulty Battery Quick Pulsing Red
CHARGING WITH THE CHARGING STAND
1. Plug the power cord of the charging stand into an outlet with the rate voltage for your unit.
2. Plug the other end into the charging stand. Note that the cord will only fit into the charging stand
with the proper orientation.
3. Ensure that the switch on the unit is in the «OFF» (O) position.
4. Check the contacts of the clipper and the battery for foreign particles and contamination.
5. Insert the clipper into the charging stand so that the top of unit is facing you and the contacts
on the clipper are aligned with the contacts on the charging stand. The top of the unit is the side
with the switch (Figure 1).
6. While the unit is being charged, the LED will pulse green until fully charged. Once the battery is
fully charged, the LED will display a continuous green light and is ready for use.
7. If the LED light will not turn on, then re-insert the clipper into the charging stand and push down
gently on the clipper to engage the contacts. Note: If the LED does not turn on then there may
be dirt or grease on the contacts of the charging stand or clipper. Clean the contacts with an approved cleaning
solution and re-insert the clipper into the charging stand. If the LED still fails to turn on then follow the return
procedure under the warranty and service section.
8. The LEDs will stay on as long as the unit is in the charging stand.
CHARGING A BATTERY USING THE CHARGING STAND
1. Check the contacts of the battery for foreign particles and contamination.
2. Insert the battery into the charging stand so that the contacts of the battery are aligned
with the contact of the charging stand (Figures 2 and 3).
3. Keep the battery in the charging stand for the recommended charging time: 100
minutes.
076076CL_078005CL_076076-810-050_078005210-050_21MLM2 (EMEA).indd 6-7 076076CL_078005CL_076076-810-050_078005210-050_21MLM2 (EMEA).indd 6-7
English
Figure 1
Figure 2 Figure 3
6
4. The battery is charging when the LED light is pulsing green. As soon as the battery is fully charged, the green
LED light will remain solid.
5. Hold the charger firmly with one hand and pull the clipper or the battery out with the other.
6. Note: Except when charging, always unplug this appliance from the electrical outlet immediately after using.
ABOUT THE LI-ION BATTERY
1. This appliance operates with a removable Li-Ion 7.2V 3000mAh battery.
2. Note: To ensure that the new battery reaches its full potential, the battery should be completely drained after
the first use. This operation will only have to be performed once.
3. It will take no more than 100 minutes for the battery to be fully charged when fully discharged.
4. To ensure the longevity of this powerful battery the clipper must be operated with properly cleaned, sharpened
and oiled blades at all times.
5. When the battery is fully charged, the clipper can be used for 120 minutes for the Cordless Model 97, or 80
minutes for the Cordless Turbo A5, without being connected to the power supply.
6. For instructions on disposal of the Li-Ion battery please refer to the "WASTE DISPOSAL" section at end of this
manual.
CHANGING THE BATTERIES
1. Move the switch to the «OFF» (O) position.
2. Push the battery interlock on the back side of the clipper, and pull the battery out of the
clipper.
3. Fit the charged battery in the clipper, until the battery interlock is engaged (Figures 4
and 5).
OPERATING THE UNIT
The appliance is designed to operate in either cordless or corded mode. The preferred method is cordless as it
ensures a longer life for the battery. Use the power cord when the batteries are not fully charged. If your appliance
did not come with a charging stand please refer to corded operation in this manual.
Always apply one to two drops of the provided Oster
lubricant to the blades before use. Wipe off excess with a clean dry cloth. When finished using, clean excess
hair from the blades using the cleaning brush and wipe the housing with a clean dry cloth. Before replacing the
blade guard for storage, disperse one or two drops of lubricating oil over the blades to prevent rusting. Cutting
efficiency may drop and the blades and motor may be damaged if hair is dirty or hair styling agents have been
applied. Always ensure that hair is clean before using the appliance.
Keep the cord straight while in use. If the cord becomes kinked or tangled, turn <<OFF>> (O) the appliance and
straighten it.
The vibration total value to which the hand-arm system is subjected, measured according to EN ISO 5349-1 and
EN ISO 5349-2, is below 2,5 m/s².
The A-weighted sound pressure level emitted by this product is below 70db.
Figure 4
Clipper & Blade Lubricating Oil or other Oster
TM TM
7
2021/10/29 下午4:59 2021/10/29 下午4:59
English
Figure 5
approved