USB-C™ PD Fast Charger (25 W)
EN
FR
USB-C™ PD Chargeur Rapide (25 W)
Notes for network separation
The product has no power switch and may be used only in
easily accessible outlets to quickly remove it in an emer-
gency and after use.
Voltage-free only with pulled plug.
• In case of emergency, during thunderstorms and after
use, pull the product on its plug housing!
• Do not open the housing.
• Do not modify product and accessories.
• Do not short-circuit connectors and circuits.
A defective device may not be put into operation, but must
be disconnected from mains and protected against fur-
ther use.
• Use product, product parts and accessories only in per-
fect condition.
• Do not repair defective products yourself.
• In case of questions, defects, mechanical damage, trou-
ble and other problems, non-recoverable by the docu-
mentation, contact your dealer or producer.
• Avoid stresses such as heat and cold, moisture and di-
rect sunlight, microwaves, vibrations and mechanical
pressure.
• Do not cover the product.
Not meant for children. The product is not a toy!
• Secure packaging, small parts and insulation against
accidental use.
2 Description and function
2.1 Product
The product is a USB charger for charging and operating
a device via a USB-C™ PD port. The product supports the
USB-C™ PD3.0 standard (PD = Power Delivery).
2.2 Scope of delivery
USB-C™ PD (Power Delivery) Fast Charger (25 W), User
Manual
2.3 Operating Elements
See Fig. 1.
1 Euro plug
3 Intended use
This product is intended exclusively for private
use and its intended purpose. This product is not
intended for commercial use.
We do not permit using the device in other ways like descri-
bed in chapter „Description and Function" or in the „Safe-
ty Instructions". Use the product only in dry interior rooms.
Not attending to these regulations and safety instructions
might cause fatal accidents, injuries, and damages to per-
sons and property.
4 Preparation
1. Check the scope of delivery for completeness and in-
tegrity.
2. Compare the specifications of all used devices and en-
sure compatibility.
5 Connection and operation
See Fig. 2.
1. Connect your device to the USB-C™ PD socket of the
charger using a suitable charging cable.
2. Plug the charger into a wall socket.
3. Disconnect all plug connections after use.
A USB charging cable is not included in the scope of de-
livery. The output voltage is automatically regulated and
adapted to the connected device. The charger does not
contain any elements to be operated during use.
REV2023-07-17
Subject to change without notice. |
V1.0anw
Sous réserve de modifications.
2 USB-C™ PD socket
6 Maintenance, Care, Storage and
Transportation
The product is maintenance-free.
NOTICE!
• Always unplug the product from the wall socket befo-
re cleaning.
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Store the product out the reach of children and in a dry
and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.
7 Disposal instructions
7.1 Product
According to the European WEEE directive, electri-
cal and electronic equipment must not be disposed
with consumers waste. Its components must be re-
cycled or disposed apart from each other. Otherwi-
se contaminative and hazardous substances can damage
the health and pollute the environment.
As a consumer, you are committed by law to dispose elect-
rical and electronic devices to the producer, the dealer, or
public collecting points at the end of the devices lifetime for
free. Particulars are regulated in national right. The symbol
on the product, in the user manual, or at the packaging all-
udes to these terms. With this kind of waste separation, ap-
plication, and waste disposal of used devices you achieve
an important share to environmental protection.
WEEE No: 82898622
7.2 Packaging
Packaging can be disposed of free of charge at the
suitable collection points – paper belongs in paper
bins, plastics belong in yellow sacks and glass be-
longs in used glass bins.
DE4535302615620
8 EU Declaration of conformity
With the CE sign Goobay®, a registered trade-
mark of the Wentronic GmbH ensures, that the
product is conformed to the basic European
standards and directives.
1 Consignes de sécurité
Le mode d'emploi fait partie intégrante du produit et com-
prend d'importantes informations pour une bonne installati-
on et une bonne utilisation.
• Lisez le mode d'emploi attentivement et complètement
avant de l'utiliser.
Le mode d'emploi doit être disponible à des incertitudes et
transfert du produit.
• Conservez soigneusement ce mode d'emploi.
Notes pour la séparation des réseaux
Le produit n'a pas d'interrupteur d'alimentation et peut être
utilisé que dans des points facilement accessibles en cas
d'urgence et rapidement après l'utilisation de cette pour
les supprimer.
Sans surcharge de tension uniquement lorsque le bou-
chon est tiré.
• Tirez en cas d'urgence directement après utilisation et
pendant les orages, branchez le boîtier de connecteur!
• Ne pas ouvrir le boîtier.
• Ne modifiez pas le produit et les accessoires.
• Pas court-circuiter des connexions et circuits.
Un appareil défectueux ne doit pas être mis en service. Il
doit au contraire être immédiatement mis hors tension et
protégé contre toute utilisation involontaire.
• Utilisez le produit, pièces et accessoires des produits
uniquement en parfait état.
• Ne réparez pas vous-même les produits défectueux.
• En cas de questions, les défauts, les dommages méca-
- 3 -
Pillmannstraße 12 | 38112 Braunschweig | Germany
65367, 65368
Material damage
Goobay® by Wentronic GmbH
