Preset Modes - Oursson PB1550HTD Manual De Instrucciones

PRODUcT SET
Measuring cup ................................................... 1 pc
Lid ...................................................................... 1 pc
Sealing ring ........................................................ 1 pc
Blender's cup ..................................................... 1 pc
Pusher ............................................................... 1 pc
Blade unit ........................................................... 1 pc
Motor unit ........................................................... 1 pc
Instruction manual ............................................. 1 pc
Warranty card .................................................... 1 pc
ELEmENTS OF DESIGN, Fig. B
Measuring cup
Lid
Sealing ring
Blender's cup
Blade unit
Device's body
Control panel
UTILIZATION, Pic. c
cONTROL PANEL, Pic. C-1
ON/OFF button is located on the bottom of the device's
body:
«О» - power off
«I» - power on
Use Rotary switch for the following functions:
• START/STOP the device
• Changing rotation's speed and time
- use this button to change the speed of rotation
- use this button to set the timer, 0-9 min.
- use this button to crush ice
- use this button to make smoothies
- use this button to make jam
- use this button to heat up
- use this button for Turbo mode
Display, Pic. C-2
1. Rotation speed indication
2. Temperature indication
3. Time indication
Before first use, make one preparation cycle without
ingredients, add water into the glass cup. After that, wipe
the body of the device with a dry soft cloth. Wash the cup,
lid, pusher, measuring cup and stainless steel knives with
warm water and detergent.
Before assembling and disassembling the device,
make sure it is unplugged.
The knives are very sharp, be careful.
12
Order of Operation:
1. Plug in the device. Turn the ON/OFF switch into the «I»
position. All the buttons and the display will light up on
the control panel, a sound signal will be heard, and then
the device will go into standby mode. To exit standby
mode, slightly press START/STOP button, all the
buttons indication and the display will light up.
2. In standby mode, install the blender's cup onto the
motor unit according to the manual.
3. Add required ingredients into the cup. Do not fill the
cup above the mAX mark. Close the cup with lid.
NOTE: The volume of the ingredients must not exceed
2/3 of the volume of the cup.
4. Select one of the preset modes (
press START/STOP once.
5. You can specify your own rotation speed and
operational time parameters. In standby mode, press
button, with the help of rotary switch set the required
rotation speed, press button again. To set the
operational time, repeat the steps using .button.
Press START/STOP once. The mixing/grinding process
will start automatically. To stop the blender, press
START/STOP again.
NOTE: If the ingredients got stuck on the cup's walls
during mixing/grinding, use the pusher. Pusher can be
used for stirring the ingredients during grinding/mixing.
Do not use the pusher for stirring more than 30 sec.
6. Remove the blender's cup from the body of the device
according to the manual. You can open the lid only
when the cup is removed from the motor unit.
7. Turn the switch at the bottom of the device to OFF
position - «О». Unplug the device. After that, you can
disassemble the device.
The device is equipped with overload and
overheating protection. If there is an overload
or an overheating, the device will automatically
stop. Unplug the device. Let it cool for 45
minutes. After that, you can continue using
the device.
When grinding hard products, do not use the
device more than for 1 minute. Let the device
cool for at least 5 minutes.
Maximum time of continues use of the blender
is 2 minutes, after that you need to turn off the
device and let it cool for 3 minutes. Do not use
the device without water or ingredients.

PRESET mODES

modes
),
Rotation speed
PREPARATION REcOmmENDATIONS
Before preparing, it is recommended to cut ingredients on 2x2x2 cm pieces. Max. amount of ingredients is shown in
the table. Follow the recommendations in the recipe book.
Operation
Smoothies and milk-
shakes
Puree from fresh
fruit, berries and
vegetables
Puree from cooked
fruits, vegetables and
soups
Kneading dough for
pancakes, omelets,
etc.
Name Description
Preset: speed 10/3 minutes, indication -
and speed is shown on the display, indication
Smoothie
Other mode's indications are turned off. Total time of
the mode is 3 minutes.
Preset: speed 10/10 sec., next speed 3/5 sec., next
speed 10/3 sec – total 6 cycles, indication -
Ice Crushing time and speed is shown on the display, indication
lit. Other mode's indications are turned off. Total time of
the mode is 1 min. 48 sec.
Preset: speed 8/2 minutes, indication -
and speed is shown on the display, indication
Jam
Other mode's indications are turned off. Total time of
the mode is 2 minutes.
Preset: speed 10, temperature 65°С, can be changed
to 35°C, 50 °C, 65°C, 80°C, indication -
Heat up and speed is shown on the display, indication
и is lit. Other mode's indications are turned off. Total
time of the mode is 9 minutes.
Press and hold button, blender operates at max
speed 10. Release the button - blender will stop.
Turbo
Maximum operation time 9 minutes. Other mode's
indications are turned off.
Manually set the required preparation time: from 0-1
min/5 sec. gap, from 2-9 min/30 sec. gap. In heat up
Timer mode you can set temperature 35°C, 50°C, 65°C,
80°C.
Manually set the required rotation speed: from 1 to 10.
Under load, the rotational speed at level 1 - 3000 ±
10% rpm, at level 10 - 27000 ± 10% rpm.
Note
1500 ml 3 min.
30-45 The ingredients must be soft or juicy (bananas, strawber-
1500 ml MAX (8-10)
sec. ries, cucumbers, etc.)
30-45 Do not puree ingredients with a temperature higher than
750 ml MAX(8-10)
sec. 80°С
30-45
1250 ml MED (4-7) Suitable for every liquid dough
sec.
Note
, set time
is lit.
Timer countdown.
, set
is Timer countdown.
, set time
is lit.
Timer countdown.
, set time
, Timer countdown.
Timer countdown.
13