Idiomas disponibles
Idiomas disponibles
Important Safety Information
Read all safety information before operating the
equipment. Save these instructions.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
To reduce the risks of fire or explosion, electrical shock
and the injury to persons, read and understand all
instructions included in this manual. Be familiar with the
controls and proper usage of the equipment.
Grounding Instructions
This product must be grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing an escape wire for
the electric current. This product is equipped with a cord having a grounding
wire with an appropriate grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
warNING - Improper installation of the grounding plug
can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the
green grounding wire to either flat blade terminal. The wire with insulation
having a green outer surface with or without yellow stripes is the grounding
wire and must be connected to the grounding pin.
Check with a qualified electrician or serviceman if the grounding instructions
are not completely understood, or if you are in doubt as to whether the
product is properly grounded. Do not modify the plug provided. If the plug
will not fit the outlet, have the proper outlet installed by a qualified electrician.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
IMPOrTaNT: Use only a 3-wire extension cord that has a 3-blade
grounding plug and a 3-slot receptacle that will accept the plug on the
product. Make sure the extension cord is in good condition. when
using an extension cord, be sure to use one heavy enough to carry the
current the product will draw. an undersized cord will cause a drop
in line voltage resulting in loss of power and overheating. a 12 gauge
cord is recommended. If an extension cord is to be used outdoors, it
must be marked with the suffix w-a after the cord type designation. For
example, a designation of SJTw-a would indicate that the cord would be
appropriate for outdoor use.
NOTE: More than 100 feet of extension cord is not recommended.
Use more hose, not more extension cord. Shorter extension
cords will assure maximum electrical power for proper
operation.
HaZarD:
GENEraL
Can cause severe injury or property damage.
PrEVENTION:
•
Read all instructions and safety precautions before operating any
equipment.
•
Follow all appropriate local, state, and national codes governing
ventilation, fire prevention, and operation.
•
The United States Government Safety Standards have been adopted
under the Occupational Safety and Health Act (OSHA). These
standards, particularly Part 1910 of the General Standards and Part
1926 of the Construction Standard should be consulted.
•
Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specifications and safety devices of the manufacturer.
•
Before each use, check all hoses for cuts, leaks, abrasion or bulging
of cover. Check for damage or movement of couplings. Immediately
English
replace the hose if any of these conditions exist. Never repair a hose.
Replace it with an identical replacement hose.
•
Do not spray outdoors on windy days.
•
Wear clothing to keep paint off skin and hair.
•
Never aim the spray gun at any part of the body.
HaZarD:
EXPLOSION HaZarD DUE TO
INCOMPaTIBLE MaTErIaLS
Will cause property damage or severe injury.
PrEVENTION:
•
Do not use materials containing bleach or chlorine.
•
Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane. They are
not compatible with aluminum.
•
Contact your coating supplier about the compatibility of material with
aluminum.
HaZarD:
EXPLOSION Or FIrE
Solvent and paint fumes can explode or ignite. Property
damage and/or severe injury can occur.
PrEVENTION:
•
Exhaust and fresh air introduction must be provided to keep the air
within the spray area free from accumulation of flammable vapors.
•
Turbine contains sparking parts. Turbine must be placed in a well
ventilated area at maximum distance from the spray area.
•
Avoid all ignition sources such as static electricity, open flames,
pilot lights, hot objects, cigarettes, and sparks from connecting and
disconnecting power cords and working light switches.
•
Use extreme caution when using materials with a flashpoint below
100° F (38°C). A fluid's flashpoint is the temperature at which vapors
from the fluid could ignite if exposed to a flame or spark.
•
Fire extinguishing equipment must be present and in working order.
•
The power cord must be connected to a grounded circuit.
•
Follow the material and solvent manufacturer's safety precautions and
warnings.
HaZarD:
HaZarDOUS VaPOrS
Paints, solvents, insecticides, and other materials can
be harmful if inhaled or come in contact with the body.
Vapors can cause severe nausea, fainting, or poisoning.
PrEVENTION:
•
Use a respirator or mask if vapors can be inhaled. Read all instructions
supplied with the mask to be sure it will provide the necessary
protection.
•
Wear protective eyewear.
•
Wear protective clothing as required by coating manufacturer.
HaZarD:
SkIN BUrN INJUry
Heated parts can cause severe skin burn injury.
PrEVENTION:
•
Quick disconnect fittings on the hose and spray gun become hot
during use. Avoid skin contact with quick disconnect fittings
when they are hot. Allow quick disconnect fittings to cool before
disconnecting the spray gun from the hose.
Service
Should your spray system need service during the warranty period,
return your unit and the proof of purchase to the distributor where it was
purchased. At our option, the unit will be repaired or replaced. In a continued
commitment to improve quality, we reserve the right to make component or
design changes when necessary.
2
© Titan Tool Inc. All rights reserved.
