Idiomas disponibles
Idiomas disponibles
ENGLISH
Minimum Gauge for Cord Sets
Volts
Ampere Rating
120 V 25' (7.6 m) 50' (15.2 m) 100' (30.5 m) 150' (45.7 m)
(Amps)
240 V
50' (15.2) 100' (30.5) 200' (61.0) 300' (91.4)
More
Not More
Than
Than
0
6
18
6
10
18
10
12
16
12
16
14
• DO NOT place any object on top of the charger or place the charger on a soft surface
that might block the ventilation slots and result in excessive internal heat. Place the
charger in a position away from any heat source. The charger is ventilated through
slots in the top and the bottom of the housing.
• DO NOT operate the charger with a damaged cord or plug.
• DO NOT operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way. Take it to an authorized service center.
• DO NOT disassemble the charger; take it to an authorized service center when service
or repair is required. Incorrect reassembly may result in a risk of electric shock,
electrocution or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This will
reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
• NEVER attempt to connect two chargers together.
• The charger is designed to operate on standard 120 volt household electrical power.
Do not attempt to use any other voltage. (This does not apply to vehicular chargers.)
BAT20-716-1390168ART.indd 7
SAFETY
Total Length of Cord
AWG
16
16
14
16
14
12
16
14
12
Not Recommended
12
Dwg Name: BAT20-716-1390168ART Dwg No: 1390168
ECO No: 24454 Pkg Dwg Ref: 1290522 Rev: A
Color Reference: N/A
BATTERY CHARGING INSTRUCTIONS
BATTERY CHARGER
• This Class B digital apparatus complies with Canadian ICES-003.
• This device complies with Part 15 of the FCC Rules and Industry Canada License-
exempt RSS standard(s). Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
BATTERY CHARGING
Your tool uses a DeWALT charger. Be sure to read all safety
instructions before using your charger.
1. Plug the charger into an appropriate outlet before inserting
the battery pack.
2. Insert the battery pack
E
into the charger, making sure the
pack is fully seated in charger. The red light will blink
continuously, indicating the charging process has started.
3. The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and
may be used at this time or left in the charger.
E
7
2/1/2017 5:27:01 PM
