Idiomas disponibles
Idiomas disponibles
22 | English
approx. 1 second and then goes out, and the LED of the
slope angle (21) lights up continuously.
Remove the power tool from the surface. Align the power
tool with the taught-in surface in the required slope angle.
The LED (22) lights up yellow if the slope angle lies in the
range +/-10° from the preset slope angle.
If a slope angle within +/– 3° of the preset slope angle is
reached, the LED (9) lights up green. To end the electronic
angle detection (EAD), press the button for the electronic
angle detection (EAD) (20) until none of the LEDs for angle
Status Indications
Status indicator for
Meaning/cause
power tool (22)
Green
Status OK
Yellow
Critical temperature has been reached, re-
chargeable battery is almost empty, or KickBack
Control is switched off
Illuminated red
Power tool has overheated or rechargeable bat-
tery is empty
Flashing red
KickBack shutdown has been triggered
Flashing blue
Power tool is connected to a mobile device or
settings are being transferred
Status indicator for power tool (9)
Green
Yellow
Flashing yellow, then briefly illuminated
green
Flashing yellow, then briefly illuminated
yellow
A) The absolute measuring accuracy can vary based on different conditions (e.g. misalignment of the tool with the screw based on the interac-
tion between screwdriver bit and/or adaptor; evenness of the surface which is referred to; etc.)
Connectivity functions
In conjunction with the Bluetooth® Low Energy Module
GCY 42, the following connectivity functions are available
for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Practical advice
With the Bluetooth® Low Energy Module GCY 42, the
u
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
Only apply the power tool to the screw when the tool
u
is switched off. Rotating application tools can slip off.
An auxiliary tool can be used to remove the screwdriver bit
or universal bit holder.
1 609 92A 6Y0 | (14.09.2021)
selection (21) are lit up (45° → 60° → User-defined → Off).
The set angle and reference surface are saved even when
changing the rechargeable battery or when waking up the
power tool from sleep mode.
User Interface (see figure D)
The user interface (14) is used to set and check a slope
angle as part of the electronic angle detection (EAD), to de-
activate the rapid shut-off (KickBack Control) and to indicate
the status of the power tool.
Meaning/cause
Selected angle is reached with a tolerance of +/– 3° to the taught-in surface
Selected angle is reached with a tolerance of +/– 10° to the taught-in surface
Surface is being taught in
Initialisation process not carried out correctly
Belt clip
You can use the belt clip (10) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always at hand.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
Solution
–
Run the power tool at no load and allow it to cool
down, replace or charge the rechargeable battery
soon, or press the KickBack button
Allow the power tool to cool down, or replace or
charge the rechargeable battery
Switch the power tool off and on again
–
A)
A)
Bosch Power Tools
