Commercial Electric CMB150-OB Instrucciones De Instalación
Commercial Electric CMB150-OB Instrucciones De Instalación

Commercial Electric CMB150-OB Instrucciones De Instalación

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

E464668
E465069
Kit Includes: 1-Box/Brace, 2-Bracket Screws, 1-Ground Screw, 2-#10-32 Mounting Screws, 1-NM Cable Connector,
1-Bracket Strap
WARNING:
Turn off power at main fuse/breaker box before beginning installation.
Wiring must meet the National Electrical Code.
This Ceiling Fan & Fixture Support meets or exceeds the requirements of the National Electrical
Code and must be used with hardware supplied to mount outlet box and fan or fixture bracket.
Only use #10 screws to support a ceiling fan. #8 screws are acceptable for fixtures. Intended for
1/2" sheetrock. Included Connector for use with Nonmetallic Cable (type N).
PRODUCT RATINGS
Nominal On-Center Joist Spacing
16"
24"
12" (CMBM150-OB ONLY)
16" (CMBM150-OB ONLY)
Step 1:
Locate the mounting location for the fixture
or ceiling fan.
Step 2:
Cut a 4" diameter hole in the sheetrock. If a
fixture is present, remove the existing fixture,
outlet box, and/or support bar.
Step 3:
Thread the adjustment screw so that the overall
length is nearly the distance between the joists.
Step 4:
See Figure 1 - Figure 2
Insert the brace through the hole and lay it on
the backside of the sheetrock. Make sure to
place the brace such that it is directly above
the center of the hole and perpendicular to
the joists.
Step 5:
See Figure 3
Turn the tube until tight. Avoid using a
wrench unless it is necessary to bring a flat
side of the tube down so that it is parallel
with the ceiling.
Step 6:
See Figure 4
Pull wire into the electrical box through the
connector provided.
Figure 1
Figure 2
Figure 3
DISTRIBUTED BY: HOME DEPOT • 2455 PACES FERRY RD., N.W. • ATLANTA, GA 30339 • FOR ASSISTANCE, CALL: 1-844-202-7486 • HOMEDEPOT.COM
Ceiling Fan & Fixture Support
CMB150-OB, CMB218-OB, CMBM150-OB
Fan Rating (lbs)
Up to 70
Up to 70
Up to 70
Up to 70
Step 7: See Figure 5
Step 8: See Figure 6
Step 9:
Step 10:
Figure 4
Installation Instructions
Insert the bracket strap up through the hole
and place onto the tube (See Figure 5A).
The bracket strap must be centered with
respect to the hole. Pull the bracket strap
down. Do not bend the bracket strap.
Place the electrical box into the hole and
align it with the bracket strap screws. Start
both mounting nuts (do not tighten yet) and
make sure everything is properly aligned.
Once aligned, tighten the nuts and bracket
screws to secure the box into place.
See Figure 7
Slide the mounting selectors to the
appropriate position. Use #8 for fixtures and
#10 for fans.
Follow the installation instructions provided
with the fan or fixture.
Figure 5
Figure 6
Figure 7
Model No.:
Fixture Rating (lbs)
Up to 150
Up to 50
Up to 150
Up to 150
Figure 5A
ACCESORIOS
VENTILADORES
FIXTURES
FANS
loading

Resumen de contenidos para Commercial Electric CMB150-OB

  • Página 1 Installation Instructions Ceiling Fan & Fixture Support Model No.: CMB150-OB, CMB218-OB, CMBM150-OB E464668 E465069 Kit Includes: 1-Box/Brace, 2-Bracket Screws, 1-Ground Screw, 2-#10-32 Mounting Screws, 1-NM Cable Connector, 1-Bracket Strap WARNING: Turn off power at main fuse/breaker box before beginning installation. Wiring must meet the National Electrical Code. This Ceiling Fan & Fixture Support meets or exceeds the requirements of the National Electrical Code and must be used with hardware supplied to mount outlet box and fan or fixture bracket.
  • Página 2 Instrucciones de instalación Ventilador de Techo y Accesorio de Soporte N.° de Cat.: CMB150-OB, CMB218-OB, CMBM150-OB E464668 E465069 Kit Incluye: 1-Caja/Soportes, 2-Tornillos de soporte, 1-Tornillo de tierra, 2-#10-32 Tornillos de fijación, 1-Conector de cable NM, 1-Soporte de la Correa ADVERTENCIA: Desconecte la energía en la caja de fusibles / disyuntor antes de comenzar la instalación. El cableado debe cumplir con el Código Eléctrico Nacional.

Este manual también es adecuado para:

Cmb218-obCmbm150-ob