Axxess BX-FD3 Instrucciones De Instalación
  1. Manuales
  2. Marcas
  3. Axxess Manuales
  4. Electrónica del Automóvil
  5. BX-FD3
  6. Instrucciones de instalación

Axxess BX-FD3 Instrucciones De Instalación

Ocultar thumbs
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Ford Data Interface with SWC Control 2011-up
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and
speed sense)
• BX-FD3 interface
• BX-FD3 harness
• 16-pin harness with stripped leads
• Female 3.5mm adapter with Brown and Brown/White wires
Axxess Integrate
Installation instructions for BX-FD3
BX-FD3
FEATURES
• Retains audio controls on the steering wheel
• High level speaker input
• Micro "B" USB updatable
INTERFACE COMPONENTS
APPLICATIONS
See inside front cover
axxessinterfaces.com
Connections to be made ........................................... 2-3
Initializing the BX-FD3..................................................4
Extra Features ...............................................................4
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
•
metraonline.com
Table of Contents
L.E.D. feedback .........................................................4
Changing radio type .................................................5
Dual assignment instructions (long button press ...7
Resetting the BX-FD3 ...............................................8
Metra recommends disconnecting the negative bat-
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Capítulos

Tabla de contenido
loading

Manuales relacionados para Axxess BX-FD3

Resumen de contenidos para Axxess BX-FD3

  • Página 1: Tabla De Contenido

    Installation instructions for BX-FD3 Table of Contents BX-FD3 Ford Data Interface with SWC Control 2011-up Connections to be made ........... 2-3 Initializing the BX-FD3..........4 Extra Features ...............4 Steering wheel audio control extra settings ....4 FEATURES L.E.D. feedback ............4 Changing radio type ..........5 • Provides accessory power (12-volt 10-amp)

  • Página 2: Important Warning

    BX-FD3 Applications Connections to be made FORD Fiesta From the 16-pin harness with stripped leads to the Edge 2011-2014 (without MyFord Touch) 2011-up* aftermarket radio: Explorer 2012-up Focus • Connect the (2) Red wires to the accessory wire. F-150 (without MyFord Touch) 2012-2014* (with a 4.2” screen) 2013-2014 Transit 2015-up • Connect the Blue/White wire to the amp turn on wire. Note: This wire must be connected for the interface to work properly.
  • Página 3 BX-FD3 Connections to be made From the BX-FD3 harness to the aftermarket radio: • For the radios listed below, connect the included female 3.5mm adapter with Brown and Brown/White wires, onto the male 3.5mm SWC jack of • Connect the Black wire to the ground wire. the BX-FD3. Any remaining wires, tape off and disregard: • Connect the Yellow wire to the battery wire. • Eclipse: Connect the steering wheel control wire, normally • Connect the Blue wire to the antenna turn-on wire Brown, to the Brown/White wire of the adapter. Then connect (if populated on the factory harness). the remaining steering wheel control wire, normally Brown/White, • Connect the Green wire to the left rear positive speaker output. to the Brown wire of the adapter. • Connect the Green/Black wire to the left rear negative speaker output. • Metra OE: Connect the steering wheel control Key 1 wire (Gray) • Connect the Purple wire to the right rear positive speaker output. to the Brown wire. • Connect the Purple/Black wire to the right rear negative speaker output.

  • Página 4: Initializing The Bx-Fd3

    * Note: If the BX-FD3 flashes (7) times, and you do not have an Alpine radio connected to • The vehicles display will display the SYNC information: it, that means the BX-FD3 does not detect a radio connected it. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.

  • Página 5: Changing Radio Type

    BX-FD3 Steering wheel audio control extra settings Attention: The Axxess Updater App can also be used to program the following (3) sub-sections as well, pending that the interface has been initialized and programmed. Radio legend Changing radio type 1. Eclipse (Type 1) 9. Valor If the LED flashes do not match the radio you have connected, you must manually program the BX-FD3 to tell it what radio it is connected to.

  • Página 6: Remapping The Steering Wheel Control Buttons

    Note: Not all radios will have all of these commands. Please refer to the owner’s “Volume-Up”. This will tell the BX-FD3 that this function is not available and manual provided with the radio, or contact the radio vendor directly for specific it will move on to the next function.

  • Página 7: Dual Assignment Instructions

    BX-FD3 Steering wheel audio control extra settings Dual assignment legend Dual assignment instructions (long button press) 1. Not allowed 9. Power 16. Fan-Down The BX-FD3 has the capability to assign (2) functions to a single button (except (not applicable in this “Volume-Up” and “Volume-Down”). Follow the steps below to program the 2. Not allowed 10. Band application) button(s) to your liking. 3. Seek-Up/Next 11. Play/Enter 17. Temp-Up Note: “Seek-Up” and “Seek-Down” come pre-programmed as “Preset-Up” and (not applicable in this “Preset-Down”...

  • Página 8: Resetting The Bx-Fd3

    Installation instructions for BX-FD3 Steering wheel audio control IMPORTANT extra settings If you are having difficulties with the Resetting the BX-FD3 installation of this product, please call our Tech Support line at 1-800-253-TECH. 1. With the radio on, turn the potentiometer: Before doing so, look over the instructions a Note: Before proceeding, remember the position the potentiometer is at. second time, and make sure the installation Left..hold for 2 seconds was performed exactly as the instructions Right..hold for 2 seconds are stated. Please have the vehicle apart and ready to perform troubleshooting steps Left..hold for 2 seconds before calling. Back to the initial position 2. The L.E.D. in the BX-FD3 will flash fast, and then flash slowly up to (16) times. Pay close attention as to how many slow flashes there are. This will help in troubleshooting, if need be.

  • Página 9: Interfase De Datos Ford Con Control Swc 2011-Up

    Instrucciones de instalación para BX-FD3 Indice BX-FD3 Interfase de datos Ford con control SWC Conexiones que se deben hacer ......2-3 Inicialización del BX-FD3 ..........4 2011-up Características adicionales ..........4 Configuraciones adicionales de control CARACTERÍSTICAS del audio del volante ...........4 Retroalimentación con L.E.D ........4 •...

  • Página 10: Aplicaciones

    BX-FD3 Conexiones que se deben hacer Aplicaciones FoRD Fiesta Desde el arnés de 16 pins con conectores pelados al Edge 2011-2014 (sin MyFord Touch) 2011-up* radio de mercado secundario: Explorer 2012-up Focus • Conecte los (2) cables rojos al cable de accesorios.
  • Página 11 • Ignore el conector DIN y el cable rojo conectado al mismo, ya que no se • Para todos los demás radios: Conecte el conector de 3.5mm del BX-FD3 utilizarán en esta aplicación. en el conector del radio de mercado secundario designado para una interfase externa de control en el volante.

  • Página 12: Inicialización Del Bx-Fd3

    • La pantalla del vehículo mostrará la información de SYNC: * Nota: Si el BX-FD3 parpadea (7) veces y no tiene un radio Alpine conectado a él, esto significa • Para acceder a AUX-IN, presione y mantenga presionado el botón MEDIA del volante que el BX-FD3 no detectó...

  • Página 13: Cambio De Tipo De Radio

    BX-FD3 Configuraciones adicionales de control del audio del volante Atención: La aplicación Axxess Updater también se puede usar para programar las siguientes (3) subsecciones también, hasta en tanto la interfase se haya inicializado y programado. Leyenda del radio Cambio de tipo de radio Si el parpadeo del foco LED no corresponde al radio que tiene conectado, debe 1.

  • Página 14: Remapeo De Los Botones Del Control En El Volante

    3. Buscar siguiente (no aplica) 4. Buscar anterior 1) Asegúrese que el BX-FD3 esté visible para que se pueda ver el parpadeo del 13. Colgado (no aplica) foco L.E.D. para confirmar el reconocimiento de los botones. 5. Fuente/Modo 14.

  • Página 15: Asignación Dual De Instrucciones (Presión De Botones Por Largo Tiempo)

    Configuraciones adicionales de control del audio del volante Asignación dual de instrucciones (presión de botones por largo tiempo) Leyenda asignación dual El BX-FD3 tiene la capacidad de asignar (2) funciones a un solo botón (excepto 1. No se permite 12. PTT “Subir volumen”...

  • Página 16: Restablecimiento Del Bx-Fd3

    Vuelta a la posición inicial problemas antes de llamar. 2. El L.E.D. del BX-FD3 parpadeará rápido, y después parpadeará lentamente hasta 16 veces. Ponga atención al número de parpadeos lentos que hay. Esto le ayudará en la resolución de problemas,...

Tabla de contenido