Axxess BX-CH4 Instrucciones De Instalación
  1. Manuales
  2. Marcas
  3. Axxess Manuales
  4. Accesorios de Automóviles
  5. BX-CH4
  6. Instrucciones de instalación

Axxess BX-CH4 Instrucciones De Instalación

Ocultar thumbs
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Chrysler Data Interface with SWC Control
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
• Retains audio controls on the steering wheel
• High level speaker input
• Can be used in non-amplified or amplified systems
• Micro "B" USB updatable
• BX-CH4 interface
• BX-CH4 harness
• 16-pin harness with stripped leads
• 4-pin harness with stripped leads
• Female 3.5mm adapter with Brown and Brown/White wires
Axxess Integrate
Installation instructions for BX-CH4
BX-CH4
2007-up
FEATURES
INTERFACE COMPONENTS
APPLICATIONS
See inside front cover
axxessinterfaces.com
Connections to be made ................................................2-4
Installing the BX-CH4 ....................................................... 4
Initializing the BX-CH4 ..................................................... 4
Adjusting the BX-CH4 ....................................................... 4
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
•
metraonline.com
Table of Contents
L.E.D. feedback ............................................................. 5
Changing radio type ..................................................... 5
Resetting the BX-CH4 ................................................... 7
Metra recommends disconnecting the negative bat-
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Capítulos

Tabla de contenido
loading

Manuales relacionados para Axxess BX-CH4

Resumen de contenidos para Axxess BX-CH4

  • Página 1: Tabla De Contenido

    Installation instructions for BX-CH4 Table of Contents BX-CH4 Chrysler Data Interface with SWC Control Connections to be made ..........2-4 Installing the BX-CH4 ............4 2007-up Initializing the BX-CH4 ............. 4 Adjusting the BX-CH4 ............4 FEATURES Steering wheel audio control extra settings L.E.D.

  • Página 2: Connections To Be Made

    BX-CH4 Applications Connections to be made CHRYSLER Grand Caravan 2008-up Liberty 2008-2012 Attention! This interface will work with models that are either factory 200 2011-2014 Journey 2009-2010 Patriot 2009-up amplified, or non-amplified. Please follow the instructions carefully for your 300 2008-2010 Magnum 2008-2009 Wrangler 2007-up model vehicle. Failure to do so will result in either no sound, or low sound. Aspen 2008-2009 Nitro 2007-2011 Wrangler Unlimited If you are unsure if your vehicle is factory amplified or not, please contact Sebring 2007-2010 Ram 1500 2009-2011 2007-up your local Dealer. MITSUBISHI Town & Country 2008-up...
  • Página 3 • Connect the Green/Purple wire to the reverse wire (if applicable). Black wires on the black 22-pin connector. • Connect the Light Green wire to the parking brake wire (if applicable). • Connect the 4-pin harness with stripped leads to the 4-pin connector with Green, • Connect the Blue/Pink wire to the VSS/speed sense wire (if applicable). Green/Black, Purple, and Purple/Black wires on the gray 22-pin connector. • Connect the Green wire to the left rear positive speaker output. From the BX-CH4 harness to the aftermarket radio: • Connect the Green/Black wire to the left rear negative speaker output. • Connect the Black wire to the ground wire. • Connect the Purple wire to the right rear positive speaker output. • Connect the Yellow wire to the battery wire. • Connect the Purple/Black wire to the right rear negative speaker output. • Connect the Blue wire to the antenna turn-on wire (if populated on the factory harness). Continued on the next page...

  • Página 4: Installing The Bx-Ch4

    • Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the Adjusting the BX-CH4 AX-SWC-PARROT (sold separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio. Audio level adjustment (factory amplified models only): Note: The radio must be updated to rev. 2.1.4 or higher software. • With the vehicle and radio turned on, turn the volume up 3/4 of the way. • For all other radios: Connect the 3.5mm jack of the BX-CH4 into the jack • With a small screwdriver, adjust the potentiometer clockwise to raise the audio on the aftermarket radio designated for an external steering wheel control level; counterclockwise to lower the audio level. interface. Please refer to the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to. • Once at a desired level, your audio level adjustment is complete.

  • Página 5: Steering Wheel Audio Control Extra Settings

    * Note: If the BX-CH4 flashes (7) times, and you do not have an Alpine radio connected to Repeat this step for the desired radio number you have selected. it, that means the BX-CH4 does not detect a radio connected it. Verify that the 3.5mm jack is 5) Once the desired radio number has been selected, press and hold the Volume connected to the correct steering wheel jack/wire in the radio.

  • Página 6: Radio Legend

    Note: If the next function on the list is not on the steering wheel, press “Volume-Up” for 1 second until the L.E.D. comes on, and then release 1. Eclipse (Type 1) 6. Pioneer and Jensen 11. Metra OE “Volume-Up”. This will tell the BX-CH4 that this function is not available and 12. Eclipse (Type 2) 2. Kenwood 7. Alpine it will move on to the next function.

  • Página 7: Dual Assignment Instructions (Long Button Press)

    18. Temp-Down 11. Play/Enter 3) Press and release the “Volume Up” button the number of times corresponding (not applicable in this application) to the new button number selected. Refer to the Dual Assignment Legend. The L.E.D. will flash rapidly while the “Volume-Up” is being pressed, and go back Resetting the BX-CH4 to a solid L.E.D. once released. Go to the next step once the “Volume-Up” has been pressed the desired number of times. 1. With the radio on, turn the potentiometer: Caution: If more than 10 seconds elapses between pressing “Volume-Up”, this Note: Before proceeding, remember the position the potentiometer is at. procedure will abort, and the L.E.D. will go out.

  • Página 8: Important

    Installation instructions for BX-CH4 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. NOWLEDGE IS OWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

  • Página 9: Interfase De Datos Chrysler Con Control Swc 2007-Up

    Instrucciones de instalación para BX-CH4 Indice BX-CH4 Interfase de datos Chrysler Conexiones que se deben hacer ........2-4 Instalación del BX-CH4 ............. 4 con control SWC 2007-up Inicialización del BX-CH4 ..........4 Ajuste del BX-CH4 ............4 CARACTERÍSTICAS Configuraciones adicionales de control del audio del volante Retroalimentación con L.E.D ........

  • Página 10: Conexiones Que Se Deben Hacer

    BX-CH4 Aplicaciones Conexiones que se deben hacer CHRYSLER Grand Caravan 2008-up Liberty 2008-2012 ¡Atención! Esta interfase funcionará con modelos que cuenten con 2011-2014 Journey 2009-2010 Patriot 2009-up amplificador de fábrica o que no estén amplificados. Siga las instrucciones 2008-2010 Magnum...

  • Página 11: Del Arnés Bx-Ch4 Al Radio De Mercado Secundario

    22 pins. • Conecte el cable verde con la salida positiva de la bocina izquierda trasera. Del arnés BX-CH4 al radio de mercado secundario: • Conecte el cable verde/negro con la salida negativa de la bocina izquierda trasera.

  • Página 12: Instalación Del Bx-Ch4

    • El conector de 3.5mm se debe usar para retener los controles en el volante. • Conecte el arnés de 16 pins con conectores pelados y el arnés BX-CH4 Para los siguientes radios, conecte el adaptador hembra de 3.5mm incluido •...

  • Página 13: Configuraciones Adicionales De Control Del Audio Del Volante

    Bajar volumen del volante hasta que el L.E.D. * Nota: Si el BX-CH4 parpadea (7) veces y no tiene un radio Alpine conectado a él, esto significa deje de parpadear. El L.E.D. permanecerá encendido aproximadamente 3 que el BX-CH4 no detectó...

  • Página 14: Leyenda Del Radio

    4. Buscar anterior 13. Colgado (no aplica) 1) Asegúrese que el BX-CH4 esté visible para que se pueda ver el parpadeo del 5. Fuente/Modo 14. Descolgado (no aplica) foco L.E.D. para confirmar el reconocimiento de los botones.

  • Página 15: Asignación Dual De Instrucciones (Presión De Botones Por Largo Tiempo)

    Configuraciones adicionales de control del audio del volante Asignación dual de instrucciones (presión de botones por largo tiempo) Leyenda asignación dual El BX-CH4 tiene la capacidad de asignar (2) funciones a un solo botón (excepto 1. No se permite 12. PTT “Subir volumen”...

  • Página 16: Importante

    Instrucciones de instalación para BX-CH4 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones.

Tabla de contenido