Enlaces rápidos
INSTALLATION INSTRUCTIONS FOR PART INSTGMOS-08
GM amplified OnStar Class II Data Bus
• Provides accessory (12-volt 10-amp)
• Retains R.A.P. (Retained Accessory Power)
• Used in amplified systems
• Retains chimes
• Provides NAV outputs (parking brake, reverse, mute, V.S.S.)
• ASWC harness included (ASWC not included)
• Retains OnStar/OE Bluetooth
• Adjustable volume for chimes and OnStar
• High level speaker input
• USB updatable
• Retains balance and fade
• GMOS-08 interface • 16-pin harness with stripped leads
• 18-pin harness to 12- and 24-pin GM harness with stripped leads
Cutting Tool • Crimping Tool • Tape • Connectors (example: butt-connectors, bell caps, etc.
1-800-221-0932
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
GMOS-08
Interface 2005-2006
APPLICATIONS
See inside front cover
KIT FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
METRA. THE WORLD'S BEST KITS.™
metraonline.com
Manuales relacionados para Axxess INSTGMOS-08
Resumen de contenidos para Axxess INSTGMOS-08
- Página 1 INSTALLATION INSTRUCTIONS FOR PART INSTGMOS-08 GMOS-08 GM amplified OnStar Class II Data Bus Interface 2005-2006 APPLICATIONS See inside front cover KIT FEATURES • Provides accessory (12-volt 10-amp) • Retains R.A.P. (Retained Accessory Power) • Used in amplified systems • Retains chimes • Provides NAV outputs (parking brake, reverse, mute, V.S.S.) • ASWC harness included (ASWC not included) • Retains OnStar/OE Bluetooth • Adjustable volume for chimes and OnStar • High level speaker input • USB updatable...
- Página 2 GMOS-08 Applications (Note: This interface will also work in vehicles listed below that are not equipped with OnStar) CHEVROLET PONTIAC Equinox 2005-2006 Torrent 2006 Caution Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.
- Página 3 GMOS-08 Connections to be made From the 16-pin harness: • Connect the Red wire to the ignition wire of the aftermarket radio • Connect the Orange/White wire to the illumination wire of the aftermarket radio. If the aftermarket radio has no illumination wire just tape off the Orange/White wire. • Connect the White wire to the left front positive speaker output of the aftermarket radio • Connect the White/Black wire to the left front negative speaker output of the aftermarket radio • Connect the Gray wire to the right front positive speaker output of the aftermarket radio • Connect the Gray/Black wire to the right front negative speaker output of the aftermarket radio • Connect the Green wire to the radio’s left rear positive speaker output. • Connect the Green/Black wire to the radio’s left rear negative speaker output. • Connect the Purple wire to the radio’s right rear positive speaker output. • Connect the Purple/Black wire to the radio’s right rear negative speaker output. • Connect the Blue/White wire to the radio’s amp turn on wire • Connect the Brown wire to the mute wire of the aftermarket radio. If the aftermarket radio does not have a Mute wire, tape up the Brown wire. • Connect the Light Green wire to the parking brake wire of the aftermarket navigation radio.
- Página 4 GMOS-08 Connections to be made From the 12- and 24-pin harness: • Connect the Yellow wire to the radio’s 12-volt battery or memory wire. • Connect the Black wire to the radio’s ground wire. • Plug the 14-pin harness into the GMOS-08 • The Black/Yellow wire is for the OnStar volume adjustment. This will be discussed in the OnStar Level Adjustment section of this instruction. Installing the GMOS-08 • With all connections completed to the aftermarket radio, plug the 24- and 12-pin harnesses into the vehicles wiring harnesses. • Reconnect the negative battery terminal. • Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to test the radio. Testing the GMOS-08 1) Turn the ignition on if not already, and then turn the radio on to verify that the radio works. Check balance and fader controls for proper operation. 2) Push the OnStar button (if equipped) to verify OnStar is working. The radio will shut off or mute, depending if the Brown wire on the 16-pin harness is connected, and OnStar will be heard through the front speakers. Turn off OnStar and the radio will turn back on.
- Página 5 GMOS-08 Chime Volume Adjustment Note: If Y91 is present on the RPO list, refer to your owner’s manual to adjust chimes. 1) With car on, shut off car and leave keys in ignition. Open the car door and leave it open. Chimes will be heard. 2) Wait 10 seconds, then with a small screwdriver adjust the potentiometer fully counterclockwise (all the way left), then clockwise to raise chime level and counterclockwise to lower the chime level. 3) When the volume is at the desired level, Potentiometer located on the 16 pin side remove the keys from the ignition. This will of the interface lock the chime volume at its current level.
- Página 6 Notes...
- Página 7 Notes...
- Página 8 INSTALLATION INSTRUCTIONS FOR PART INSTGMOS-08 IMPORTANT WARNING This product includes instructions for installation which must be carefully followed. The instructions are worded in such a manner to assume that the installer is capable of completing these type of electronic installations. If you are unclear as to what you are instructed to do or believe that you do not understand the instructions so as to properly and safely complete the installation you should consult a technician who does have this knowledge and understanding. Failure to follow these instructions carefully and to install the interface as described could cause harm to the vehicle or to safety systems on the vehicle. Interference with certain safety systems could cause harm to persons as well.