Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTALLATION 3
1
2
4
WARNING: Make sure the power is off.
1.
Unscrew the front 2 screws.
2.
Connect the white wires from the fixture to the white wires from the supply circuit, the black wires from fixture to the black
wires from the supply circuit, and the ground wire (green) from the supply circuit using the wire connectors .
3.
Tighten the front 2 screws to secure the fixture.
4.
Attach the photocell to the fixture by turning it clockwise.
COLOR TEMPERATURE ADJUSTMENT
3
This area light features a user-adjustable color temperature.
Measured in Kelvin [K], it is adjustable from Soft White
[~3000K] to Bright/Cool White [~3800K], to Daylight
[~5000K]. To adjust the color temperature, rotate the
button shown in the diagram.
4
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
TROUBLESHOOTING
• The light comes on during the day - The fixture may be installed in a relatively dark location, please relocate the fixture.
• The light flashes - Something is reflecting the light, please relocate the fixture away from reflective surfaces.
CARE AND MAINTENANCE
WARNING: Always make sure that the light is cooled down before attempting to clean it.
• Turn OFF all power to circuit at main circuit breaker or fuse box. DO NOT rely on wall switch alone to turn off power.
• Clean surfaces with a mild, non-abrasive cleaner.
WARRANTY
If this product fails due to a defect in materials or workmanship within five (5) years from the date of purchase, return it along
with proof of date of purchase and it will be replaced with the same or comparable model free of charge. This warranty is void
if damage or defect has resulted from accident, abuse, misuse or faulty repair. This warranty gives you specific legal rights a
you may have other rights that vary from state to state.
All product warranties are covered by Lutec USA LLC.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND
ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
SPECIFICATIONS
Watts:
56W
Lumens:
5000lm
Color temperature:
3000K-5000K
Use environment:
Wet location
Voltage:
120VAC
© 2019 Stanley Black & Decker, Inc.
STANLEY® and the STANLEY Logo are trademarks of Stanley Black & Decker, Inc. or one of its affiliates, and are used under license.
If this product ever fails, Lutec USA LLC. will replace it. DO NOT RETURN PRODUCT TO STORE.
Simply call 1-877-714-8669 toll-free, 8:30 a.m. - 5:00 p.m. ET(Enter correct times and contact dates), Monday-Friday (Contact Email:
Please note: Calls made from outside the US will be charged international rates & 1-(704)980-4135.
www.stanleytools.com
For more information visit www.stanleyledlighting.com
nd
5
Tabla de contenido
