Tabla de contenido
EN
SAFETY INSTRUCTIONS
1. Study, understand, and follow all instructions before operating the device.
2. Do not exceed rated capacity.
3. Prior to use, make sure the press is securely anchored.
4. The press shall be installed and operated in accordance with instructions.
5. Ensure the work area is clean and free of any hazards before operation.
6. Keep hands, arms, feet, and legs out of the work area. Accidental slippage can result in personal injury.
7. Use appropriate guarding to contain any pieces that may break or fly apart when applying force.
8. Use only press accessories having a capacity rating equal to or greater than the capacity of the press.
9. Verify lift cables are slack before pressing on the bolster.
10. Avoid off-center loads.
11. No alterations shall be made to the product.
12. Do not use this press for any use other than the manufacturer specified usage.
13. Failure to heed and understand these instructions and markings may result in personal injury, property damage, or
both.
Technical Data
Model
BWR5231
Capacity
10 Ton
Bed Opening
110 mm
Work Range
0-350 mm
Stroke Length
175 mm
Inside Bed Dimensions
110x340 mm
Dimensions
680x450x1070 mm
ASSEMBLY INSTRUCTIONS
Use the exploded drawing as your guide to assemble. Lay all parts and assemblies outin front of you before beginning. The following procedure is recommend-
ed:
•Attach the two base sections (8) to the upright frame (4) using bolts (9), washers (10),spring washers (11) and nuts (12).
• Insert the hydraulic cylinder (3) from the top side of frame. Once the cylinder is inserted into the frame support plate make sure that round lifting ring is
seated flat on the cylinder support plate. Then attach the round threaded nut (5) to the hydraulic cylinder. Turn clockwise to screw the round nut onto threaded
shaft on the ram. Tighten round nut (5).
• Insert the rods (16) into the bottom holes on the frame, then insert the bed flat (7) into press frame, onto the rods.
• Attach the pump assembly (20) to the right frame using screws (17,13), washers (21,15) and spring washers (18,14).
• Locate the hydraulic hose fitting on the cylinder and assemble the pressure gauge (1) to the pressure gauge connection fitting , on the top of the hydraulic
cylinder (3).
BEFORE FIRST USE
• Before first use of this product, purge away air from the hydraulic system: open the release valve by turning it counterclockwise. Pump several full strokes to
eliminate any air in the system.
• Check all parts and conditions, if there is any part broken, stop using it and contact your supplier immediately.
OPERATING INSTRUCTIONS
WARNING! ENSURE THAT YOU READ, UNDERSTAND AND APPLY THE SAFETY INSTRUCTIONS AND WARNINGS BEFORE USE.
•Place the heel block on press bed frame, then insert workpiece onto the heel block.
•Close the release valve by turning it clockwise until it is firmly closed.
•Pump the handle until serrated saddle nears workpiece.
•Align workpiece and ram to ensure center-loading.
•Pump the handle to apply load onto workpiece.
•When work is done, stop pumping the handle, slowly and carefully remove load from workpiece by turning the release
valve counterclockwise in small increments.
• Once ram has fully retracted, remove workplace from bed frame.
MAINTENANCE
•Clean the outside of the press with dry, clean and soft cloth and periodically lubricate the joints and all moving parts with a light oil as needed.
•When not in use, store the press in a dry location with ram and piston fully retracted.
•When press efficiency drops, purge always air from hydraulic system as described before.
•Check the hydraulic oil; remove the oil filler nut on the top of the reservoir, if the oil is not adequate, fill with high quality hydraulic jack oil as necessary, then
replace the oil filler nut, purge away air from the hydraulic system.
2
(LxW)
(LxWxH)
WWW.NIKOLAOUTOOLS.GR
Fig. 1
Tabla de contenido
