Idiomas disponibles
Idiomas disponibles
Jumpstart manual inside
27-01-2005
J U M P
S T A R T A N
Jumpstart must be fullly charged to jumpstart an engine.
If your vehicle's battery is too weak to start your car you can use the Jumpstart System to start it.
Make sure that the vehicle's accessories are all turned off (lights, AC, heater, radio, etc).
For maximum power, make sure all switches on the Jumpstart System are turned off, including the
Rotary Switch on the side of the unit. Securely connect the red positive (+) booster clamp to the
corresponding positive (+) terminal of your vehicle's battery.Then securely connect the black
negative (-) booster clamp to a grounding point such as the metal of the vehicle frame, as far
away from the battery as possible. DO NOT connect in to the negative battery terminal.
Turn the Rotary Switch to the "ON" position. Start your vehicle. Once the vehicle has started,
4
turn the Rotary Switch to "OFF", disconnect the black negative clamp first and then the red
positive clamp.
NOTE: If your vehicle does not start within 10 seconds, allow the Jumpstart System internal
battery to cool for 3 minutes before attempting to start the vehicle again.
Do not attempt to operate 12 volt accessories from the Jumpstart System while you are trying to
jumpstart your vehicle.
P O W E R F O R Y O U R 1 2 V O L T A C C E S S O R I E S
The 12 volt power outlet will operate most 12 volt accessories with a draw of 10 amps of less.
When fully charged the Jumpstart System will supply power to a 10 amp accessory for
approximately one hour, a six amp accessory for approximately two hours and a four amp
accessory for approximately three hours.
Make sure the 12 volt Power Outlet Switch is in the "OFF" position. Remove the protective cover
from the 12 Volt Power Outlet and plug in your 12 volt accessory.Turn the power switch to the
"ON" position.
NOTE:The 12 volt Power Outlet is protected by an internal circuit breaker that prevents damage
to the unit in case of short circuit or overdraw current. If circuit breaker is tripped, turn power
switch off and disconnect 12 volt accessory. Allow to sit for 30-40 minutes to automatically reset
circuit breaker. Have 12 volt accessory checked for possible defect before reusing.
13:32
Pagina 6
E N G I N E
W A R N I N G S
•
Do not allow the positive and negative booster clamp of the Jumpstart System to come into
contact with each other (or a common piece of metal) at any time. Sparking, an explosion, or
damage to the unit may result.
•
When jumpstarting a vehicle, make sure that the positive and negative booster clamps are
properly connected to the vehicle and battery. Failure to connect the clamps properly may cause
sparking, an explosion or damage to the unit.
•
Always wear eye protection when working with batteries.
•
If battery acid comes into contact with eyes, flush the eyes with water for at least 10 minutes.
Seek medical attention immediately.
•
If skin or clothing come into contact with battery acid, immediately wash the affected area with
soap and water. Seek medical attention.
•
Be sure to remove all metal items ( watches, necklaces, rings, etc.) before using the Jumpstart
System.
•
Always turn the Jumpstart System off when not in use. Store in a cool, dry place.
•
Do not open the Jumpstart System.There are no user seviceable parts in this unit. Doing so wil
void the warranty.
S P E C I F I C A T I O N S
Voltage:
12 Volt
Battery (built-in):
18 Amp. Sealed lead acid rechargeable battery
DC Output:
12 Volt
Boost Rate:
Up to 500 cranking amps
Circuit Breaker:
12 Volt, 10 Amp. (for DC Power Outlet) – Auto Reset
Work Light:
12 V 3 Watt bulb
5
4
