Idiomas disponibles
Idiomas disponibles
GB
Installing and removing the mixer
Place the mixer on a level and stable surface. Make sure that all the suction cups at the base have gripped the ground.
Press the lever (II) according to the arrow direction, this lever releases the latch of the working head and causes it to lift. The head
lifts up automatically with the spring, but lift it by hand and make sure that the top position of the mixer head is locked. It is not
possible to lower the head without pressing the lever again.
Install the bowl in the base opening. Insert the tongues in the base of the bowl into the grooves on the circumference of the base
opening (III) and then turn the bowl in the direction indicated by the arrow in the base (IV). This will block the bowl at the base of
the mixer. Check that installation is correct, if the bowl is secured evenly and cannot be lifted, this means correct installation (V).
Around the mixer handle tip you should install the bowl cover. Put the head cover so that the arrow, which is visible on the cover,
points to the open padlock symbol on the mixer head (VI). Make sure that the cover evenly adheres to the head and turn it, so that
the arrow points to the closed padlock icon (VI).
At the end of the spindle you should install the appropriate tip. The spindle tongues must cover the grooves around the tip hole
(VII). Push the tip upwards and turn it in the direction of the locked padlock symbol visible on the upper part of the tip flange
(VIII).
Press the lever and lower the mixer head, the device is ready for operation (IX).
Remove the mixer in reverse sequence to the assembly procedure.
Use of the device
CAUTION! Wash and dry all food contact parts thoroughly before using the machine for the first time. You must first learn the
method of device maintenance.
The device has a switch that allows you to set several rotational speeds and the turbo gear. By setting the switch to the desired
position you can determine the rotation speed of the agitator and blender. The turbo position allows to use the maximum rotational
speed. To use it, turn the control switch and hold it in the position described as "Turbo". After releasing the pressure, the switch
will automatically return to the "0" position, and device will shut down the engine speed. The positions described as 0 - 6 do not
require the switch to be held.
CAUTION! Before connecting the plug, make sure that the power switch is in position "0" – OFF.
When the plug of the power cord is plugged into the mains outlet, a control light flashes around the switch when the "0" setting is
set. Any other setting in the range 1-6 and "Turbo" causes the control light to illuminate with a standby light.
Due to the exchangeable tips, the mixer can be used to mix different food products.
The dough agitator is used to mix ingredients into medium density mixtures (e.g. yeast dough), it is recommended to use the
switch settings from the 1 – 2 range during operation with this tip.
The whipping agitator is used to mix ingredients into low density mixtures (e.g. sponge cake), it is recommended to use the switch
settings from the 1 – 4 range during operation with this tip.
The beating agitator is used for whipping foam and whipped cream, it is recommended to use the switch settings from the 5-6
range during operation with this tip.
It is advisable to gradually increase the tip rotational speed in order to avoid excessive splashing of the mixed components. The
cover of the bowl has an opening, thanks to which you can add further components without lifting the mixer head. Do not exceed
the maximum operating time of 6 minutes. Longer operating time can lead to overheating and irreparable damage of the device.
The device is equipped with safety switches which do not allow to start the device when the head is lifted or when the blender or
the blender slot cover is not properly installed. This minimises the risk of user exposure to moving parts of the device. However,
it should be taken into account that after switching the engine off, moving parts may still rotate for some time.
Do not exceed the maximum capacity of the bowl and jug, and take into account that ingredients can increase their volume when
mixed with air. It is advisable to prepare several smaller portions instead of one large.
CONSERVATION AND STORAGE
CAUTION! Never immerse the housing and head in water or any other liquid. This may cause an electric shock.
The parts that are suitable for immersion are: the bowl, the bowl cover, all the agitators, the jug cover.
After use, turn off the unit, wait until the moving parts have come to a complete stop, unplug the power cord from the mains outlet,
disassemble the device, empty the bowl or the jug from its contents, and proceed with maintenance.
Clean the parts of the device that have come into contact with food immediately after use. Dry food residues can jam agitators and
blades, which can lead to a decrease in the efficiency of the device or even damage it. However, if such a case occurs, immerse
those parts which are described as being capable of being immersed in warm water with the addition of dishwashing liquid and
allow them to soak, then clean with a soft sponge or brush and water with dishwashing liquid. None of the device parts is suitable
for washing in a dishwasher. This may lead to the loss of shape, colour, texture of the materials from which they are made.
Clean the device housing and jug external surfaces with a soft cloth, moistened with solution of water and mild cleanser. Wipe it
O R I G I N A L
I N S T R U C T I O N S
10
