4.5
Después de Terminar el Trabajo
4.5.1
Cuidados
Siempre limpie la maquina. Para tanto, deslíguela físicamente del soquete.
Nunca limpie la maquina antes de su PARADA COMPLETA.
Recoloque todos los componentes de la maquina en sus lugares, antes de
ligarla otra vez.
Al verificar la tensión de las correas, NO coloque los dedos entre las correas y
las poleas.
4.6
Manutención
4.6.1
Peligros
Con la maquina ligada cualquier operación de manutención es peligrosa.
DESLÍGUELA FÍSICAMENTE DE LA RED ELÉCTRICA, DURANTE TODA LA
OPERACIÓN DE MANUTENCIÓN.
Siempre desconecte la maquina de la red eléctrica en cualquier caso de
4.7
Aviso
La manutención eléctrica o mecánica debe ser hecha por una persona
calificada para hacer el trabajo.
La persona encargada por la manutención debe certificarse que la maquina
trabaje bajo condiciones TOTALES DE SEGURIDAD.
5. ANÁLISIS Y SOLUCIÓN DE PROBLEMAS
5.1 Problemas, Causas y Soluciones
La Sierra para Huesos Modelo SI-282HD fue diseñada para que necesite
un mínimo de manutención. Sin embargo, pueden ocurrir algunas irregularidades
en su funcionamiento, debido al desgaste natural causado por su uso.
Caso haya algún problema con su maquina, verifique la Tabla - 02 abajo,
donde están indicadas algunas soluciones recomendadas.
* La vida de servicio - 2 años para la jornada de trabajo normal
IMPORTANTE
emergencia.
23
5. 2 Adjustment and Components Substitution
5. 2. 1 Blade regulation
With daily use the Band Saw model SI-282HD Blade may suffer a light
stretching, because the Blades are elastic. Therefore check the Blade tension before
starting to work . Turn clockwise the Blade Tension Regulator No.01 (Pict.01) until the
Blade is at the right working tension.
5. 2. 2 Cut Regulator Adjustment
The Cut Regulator has been developed to help cutting and for the operator
safety. Its main purpose is to assure meat slices homogeneous thickness .
To adjust the Cut Regulator proceed as follows:
Turn the Handle No. 16 (Pict.01) counter clockwise to be able to move the Cut
Regulator.
Using the Spherical Handle No. 16 (Pict.01) move the Cut Regulator on the
Fixed Table, increasing or decreasing the distance from the Blade, as it is needed.
Finally, turn the Handle No. 16 (Pict.01) clockwise to block it at the desired
position.
5. 2. 3 Blade Guide Adjustment
The Blade Guide No. 08 (Pict.01) shall be adjusted in accordance with the height
of the product to be cut. Its purpose is to keep the Blade inflexible and perpendicular to
the Table.
To adjust the Blade Guide No. 08 (Pict.01) the Blade must be still and the Band
Saw switched off. Proceed as follows:
Turn the Handle No. 17 (Pict.01) counter clockwise to allow a vertical movement.
Adjust the guide as near as possible to the upper height of the product to be cut.
However the guide shall not impeach the free product movement.
To end it, turn the Handle No. 17 (Pict.01) clockwise to block the Blade Guide at
the desired height.
5. 2. 4 Upper Wheel Adjustment
Upper Wheel adjustment has the purpose to centralize the Blade on Wheels
avoiding it to fall off.
To adjust the Upper Wheel proceed as follows with the Band Saw disconnected
from power source:
Loose the Blade No. 09 (Pict.01) using the Blade Tension Regulator No. 01
(Pict.01), turning it counter clockwise as described in item 3.2.3.
Take away the Frame Back Lid.
Loose Nut No. 01 (Pict.02) with 13mm spanner.
Using a 13mm fixed spanner turn Screw No. 02 (Pict.02) counter clockwise if the
Blade No. 09 (Pict.01) is bending backwards, or turn Screw clockwise if the Blade is
bending towards the front of machine.
Tight the Nut No. 01 (Pict.02) with the above mentioned spanner.
Adjust the Blade tension as described in 5.2.1.
Turn Upper Wheel manually and check if the Blade is centralized on the Wheel.
Keep turning the Wheel until Blade is centralized.
12