Standby Mode; Brewing Coffee - SOLAC CE4520 Instrucciones De Uso

Downloaded by: pd-oliana on 12-08-2022 14:11 CEST
USE:
Connect the appliance to the mains.
Use the On/Off switch to switch the appliance on.
The indicator lights on the buttons will flash, indicating
that preheating is taking place.
When the preheating operation has finished, the lights
will remain lit. The buttons will not work during the pre-
heating operation.
The machine is now ready to make your coffee.

STANDBY MODE

Once the machine is switched on, it automatically goes
into Standby mode, awaiting a command.
In Standby mode the 1-coffee and 2-coffee lights stay
lit, and the thermoblock technology maintains the tem-
perature.

BREWING COFFEE

One coffee
Remove the filter holder, if it is already fitted.
To enjoy the full aroma of the coffee, we recommend
emptying and cleaning the filter with a fine cleaning
brush after each use.
Fill the coffee filter with 7-8 g of ground coffee, and
press it down using the compactor on the measuring
spoon.
Place the filter in the filter holder and fit the filter holder
in the machine, turning it anticlockwise to its locking
position.
NOTE: We recommend natural roast coffee. Torrefacto
coffee may affect the operation of the machine.
Press the 1-coffee button. The machine will start PRE-
BREWING by pouring a little water over the coffee to
moisten it. It will then brew the coffee and stop automa-
tically, with three beeps to signal the end of the function.
Once the function has finished, proceed to clean the
filter.
Two coffees
Repeat all the previous steps, substituting the 1-coffee
filter for the 2-coffee one and filling it with approximately
15-16 g of coffee.
Press the 2-coffee button and the machine will operate
until brewing is completed.
Coffee capsule (Only on the Taste Slim ProCap model)
Open the capsule accessory lid by turning it anti-cloc-
kwise.
Place the capsule face up inside the space and close
the lid.
Put the accessory into the filter holder, positioning the
lid at the bottom of it.
Proceed to brew the coffee as normal.
To extract the capsule, remove the filter holder and
allow it to cool.
Take off the lid and recycle the capsule as recommen-
ded by the capsule manufacturer.
Hot water
In Standby mode, open the steam/hot water control.
The pump will start to work and hot water will come out
through the steamer pipe.
Once finished, close the pipe using the steam control.
Steam / Frothing Milk
In Standby mode, press the steam button. This will start
to flash, indicating that the thermoblock is heating to a
temperature of 130 ºC to produce dry steam.
Insert the steamer pipe into the container holding the
milk or liquid to be heated.
Open the steam/hot water control. The pump will emit
small pulse sounds, generating steam.
Once the milk or liquid is hot, close the steam control
and wipe the pipe clean with a cloth.
When the function has finished, press the coffee button
to lower the temperature and switch back to Standby
mode.
COFFEE QUANTITY PROGRAMMING
With this coffee it is possible to set the amount of coffee
that each button brews. To do this, make a coffee by fo-
llowing the instructions above, changing only one step:
When pressing the button to brew the coffee, keep it
pressed down until you reach the desired quantity and
then release it.
The machine saves this setting for subsequent brews.
The time can be set from 20 to 75 seconds. (25 ml –
160 ml)
PROGRAMMING THE COFFEE MAKER
Programming menu
First, make sure that the coffee maker is in Standby
mode.
Next, press and hold the steam heating button for 5
seconds.
The lights on the buttons will flash consecutively. The
programming menu has now been accessed.
NOTE: If the machine remains inactive for 15 seconds,
it automatically switches back to standby mode.
Programming the temperature
Access the programming menu.
Press the 1-coffee button to enter the temperature set-
ting. Once pressed, the machine uses the lights to show
which level it was at:
1-coffee 2-coffees
X
X X
X X
* Temperature may vary depending on external condi-
tions.
EN
Steam Level
Low
temperature
(70 ±5* ºC)
Medium
temperature
(75 ±5* ºC)
X High
temperature
(80 ±5* ºC)